German, 20.11.2020 21:50 barattah

Erganzen Sie;
Wo (arbeiten) du? Bei Siemens?
Ja, ich

Answers: 3

Show answers

Another question on German

German, 05.07.2019 18:00

Memeee for my german homework eehe

Answers: 2

Answer

German, 06.07.2019 07:00

How many members are there in the house of representatives

Answers: 2

Answer

German, 09.07.2019 16:00

This is a question in my german class and i'm not sure how to word my answer.from what you know about albert einstein, why do you think he is such an important historical figure?

Answers: 1

Answer

German, 10.07.2019 15:00

Answer the questions. use the words in the list.

Answers: 1

Answer

You know the right answer?

Erganzen Sie;
Wo (arbeiten) du? Bei Siemens?
Ja, ich...

Questions

Engineering, 14.09.2019 02:10

The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero....

Engineering, 14.09.2019 02:10

The flow of a real fluid has (more —less - same ) complexity of an ideal fluid, owing to the phenomena caused by the existence of (viscosity-pressure...

Engineering, 14.09.2019 02:10

In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...

Engineering, 14.09.2019 02:10

Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...

Engineering, 14.09.2019 02:10

Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...

Engineering, 14.09.2019 02:10

Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...

Engineering, 14.09.2019 02:10

Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...

Engineering, 14.09.2019 02:10

Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...

Engineering, 14.09.2019 02:10

The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...

Engineering, 14.09.2019 02:10

Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...

Engineering, 14.09.2019 02:10

Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...

Engineering, 14.09.2019 02:10

Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...

Engineering, 14.09.2019 02:10

Draw and label a typical true stress-strain curve for a ductile material....

Engineering, 14.09.2019 02:10

Draw and label a typical engineering stress-strain curve for a brittle material....

Engineering, 14.09.2019 02:10

Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...

Engineering, 14.09.2019 02:10

Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...

Engineering, 14.09.2019 02:10

It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...

Engineering, 14.09.2019 02:10

For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...

Engineering, 14.09.2019 02:10

Which of the two materials (brittle vs. ductile) usually obtains the largest modulus of toughness and why?...

Engineering, 14.09.2019 02:10

Afour-cylinder chrysler si engine has the following characteristics: 2.2l displacement, 87.5 mm bore, 92 mm stroke, 8.9 compression ratio, and a maxi...

More questions: German Another questions

Erganzen Sie; Wo (arbeiten) du? Bei Siemens? Ja, ich

Answers

Another question on German

Erganzen Sie;
Wo (arbeiten) du? Bei Siemens?
Ja, ich