Mathematics, 08.01.2020 22:31 jonathanjenkins701

Marginal utility can be rev: 04_09_2018 multiple choice positive, but not negative. positive or negative, but not equal to zero. positive, negative, or equal to zero. decreasing, but not negative.

Answers: 1

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 14:30

Shania's test scores in 8 subjects were 88, 91, 85, 74, 69, 72, 80, and 87. shania found the middle number of her scores. which type of measure did she find?

Answers: 1

Answer

Mathematics, 21.06.2019 17:00

Rectangle leg this 11feet and perimeter of 38feet what is the width of the rectangle in feet

Answers: 1

Answer

Mathematics, 21.06.2019 17:30

8000 + 8800 + 8000 + 8 million + 80 trillion + another a katrillion equals

Answers: 1

Answer

Mathematics, 21.06.2019 21:50

Ab and bc are tangent to circle d. find x is ab = 3x + 8 and bc = 26. find x

Answers: 1

Answer

You know the right answer?

Marginal utility can be rev: 04_09_2018 multiple choice positive, but not negative. positive or neg...

Questions

Engineering, 26.07.2019 19:30

The uniform wall thickness that is usually targeted for plastic injection molded parts is roughly: a. 0.5 mm b. 3 mm c. 7 mm d. 12 + mm...

Mathematics, 26.07.2019 19:30

A\greend{4\,\text{cm} \times 6\,\text{cm}}4cm×6cmstart color greend, 4, space, c, m, times, 6, space, c, m, end color greend rectangle sits inside a c...

Engineering, 26.07.2019 19:30

Steam at 320 c flows in a cast iron pipe (k = 80 w/mk) whose inner and outer diameters are 5 cm and 5.5 cm respectively. the pipe is covered with 3 cm...

Engineering, 26.07.2019 19:30

Why do cementite plates appear as dark lines in the fine pearlitic microstructure when viewed under a general optical microscope?...

Engineering, 26.07.2019 19:30

Acoil of wire 8.6 cm in diameter has 15 turns and carries a current of 2.7 a. the coil is placed in a magnetic field of 0.56 t. what is the magnitude...

Engineering, 26.07.2019 19:30

Which of the following can be seen in the results of a uniaxial tension test mark all that apply? a. the material's toughness b. the material's yield...

Engineering, 26.07.2019 19:30

According to caplan, we should view ethical issues in science and medicine as simple engineering problems. a)- true b)- false...

Engineering, 26.07.2019 19:30

According to caplain, who is chiefly responsible for constantly inquiring into the nature of the ethical questions posed by the work of engineers? a)...

Engineering, 26.07.2019 19:30

Describe the importance of ferrite and austenite stabilizing elements in steels...

Engineering, 26.07.2019 19:30

Which of the following statements is/are true about typical metals (mark all that apply): a. for a pure metal (not an alloy), solidification takes pl...

Engineering, 26.07.2019 19:30

You have 2 tensile specimens of different materials but which are otherwise identical. at a load of 100n, which will show the lower strain: (a).the s...

Engineering, 26.07.2019 19:30

Which is true with respect to part tolerances? a)-they have no impact on the overall manufacturing cost of a part. b)- the dictate the selection of m...

Engineering, 26.07.2019 19:30

Which is/are false of steel (mark all that apply)? a)-steel is any fe-c alloy with carbon content > 2.1% b)- heat treatment of steel makes use of...

Engineering, 26.07.2019 19:30

Which is/are true of cutting processes mark all that apply? a)-the power required is proportional to the metal removal rate b)- the shear angle is th...

Engineering, 26.07.2019 19:30

Which of the following is/are not an alloy (mark all that apply)? a. type m tool steel b. stainless steel c. titanium d. brass e. inconel...

Engineering, 26.07.2019 19:30

Which of the following quenching materials is least severe in its quenching action (slowest cooling)? a. air b. brine c. oil d. water...

Engineering, 26.07.2019 19:30

Which of the following is/are false about refining aluminum from the ore state (mark all that apply) a)- a blast furnace is used b)-the ore is called...

Engineering, 26.07.2019 19:30

Which is/are not a mechanism commonly associated with tool wear (mark all that apply)? a. adhesion b. attrition c. abrasion d. coercion...

Engineering, 26.07.2019 19:30

Which of the following is/are not a common crystal structure in metals (mark all that apply)? a. face-centered cubic (fcc) b. face-centered orthorhom...

Engineering, 26.07.2019 19:30

At steady state, a well-insulated compressor takes in air at 100f ,14.2 lbf/in^2, with a volumetric now rate of 1200 /min, and compresses it to 500°f,...

More questions: Mathematics Another questions