Scarlett tried to shade all the factors of 15 on the hundred chart.

the results from a pre-test for students for the year 2000 and the year 2010 are illustrated in the box plot. what do these results tell us about how students performed on the 29 question pre-test for the two years?

if we compare only the lowest and highest scores between the two years, we might conclude that the students in 2010 did better than the students in 2010. this conclusion seems to follow since the lowest score of 8 in 2010 is greater in value than the lowest score of 6 in 2000. also, the highest score of 28 in 2010 is greater in value than the highest score of 27 in 2000.

but the box portion of the illustration gives us more detailed information. the middle bar in each box shows us that the median score of 20 in 2000 is greater in value than the median score of 17 in 2010. further, we note that the box and whiskers divide the illustration into four pieces. each of these four pieces represents the same portion of students. so, the upper half of the students in 2000 scored in the same score range as the upper one-fourth of the students in 2010, see the illustration at a score of 20.

by considering the upper one-fourth, upper half, and upper three-fourths instead of just the lowest and highest scores, we would conclude that the students as a whole did much better in 2000 than in 2010. we would conclude that as a whole the students in 2010 are less prepared than the students in 2000.

in this section, we discuss box-and-whisker plots and the five key values used in constructing a box-and-whisker plot. the key values are called a five-number summary, which consists of the minimum, first quartile, median, third quartile, and maximum.

step-by-step explanation:

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).

answer: options

step-by-step explanation:

in geometry, parallel lines are lines in a plane which do not meet; that is, two lines in a plane that do not intersect or touch each other at any point are said to be parallel. by extension, a line and a plane, or two planes, in three-dimensional euclidean space that do not share a point are said to be parallel.