subject

Mathematics, 31.01.2021 18:00 Anasiabrown11

Goodmorning I need help with this question. And may you explain to me how to get this right step by step. Thank you.

Goodmorning I need help with this question. And may you explain to me how to get this right step by

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 23:00

Using only odd number for numerators write two different subtraction problems that have a difference of 3/4

Answers: 1

question

Mathematics, 21.06.2019 23:40

You are saving to buy a bicycle; so far you save 55.00. the bicycle costs 199.00. you earn 9.00 per hour at your job. which inequality represents the possible number of h hours you need to work to buy the bicycle?

Answers: 2

question

Mathematics, 22.06.2019 01:30

Find the vertex for the parabola given by the function ƒ(x) = −3x2 − 6x.

Answers: 2

question

Mathematics, 22.06.2019 02:30

The price of a visit to the dentist is \$50$50. if the dentist fills any cavities, an additional charge of \$100$100 per cavity gets added to the bill. if the dentist finds nn cavities, what will the cost of the visit be?

Answers: 2

You know the right answer?

Goodmorning I need help with this question. And may you explain to me how to get this right step by...

Questions

question

Chemistry, 13.09.2019 23:20

The enthalpy of vaporization of h2o at 1 atm and 100 c is 2259 kj/kg. the heat capacity of liquid water is 4.19 kj/kg-c, and the heat capacity of wate...

question

Chemistry, 13.09.2019 23:20

Calculate the cell potential for a cell operating with the following reaction at 25 degrees celsius, in which [mno4^1-] = .01m, [br^1-] = .01m, [mn^2+...

question

Chemistry, 13.09.2019 23:20

An aqueous solution of nazco3 saturates at 300 k to form, nazco3.3h2o crystals. 10 kg/h of 35 mass% aqueous solution enters a continuous evaporative c...

question

Chemistry, 13.09.2019 23:20

The halpy of vaporization of h2o at 1 atm and 100 c is 2259 kj/kg. the heat capacity of liquid water is 4.19 kj/kg. c, and the heat capacity of water...

question

Chemistry, 13.09.2019 23:20

Prepare benzoic acid from benzyl alcohol.5 ml of sodium hydroxide, water and potassium manganese are added. how could you tell when the reaction...

question

Mathematics, 13.09.2019 23:20

When given a graph, the vertical line test can be used to determine functionality. describe the vertical line test and explain the reasons why a graph...

question

Engineering, 13.09.2019 23:20

Two factors that can be modified to optimize the cutting processes are feed and depth, and cutting velocity. a) true b) false...

question

Engineering, 13.09.2019 23:20

The highest cutting temperature is located close to the shear zone. a) true b) false...

question

Engineering, 13.09.2019 23:20

The largest source of heat generated in metal cutting is due to friction. a) true b) false...

question

Engineering, 13.09.2019 23:20

Calculate the differential pressure in kpa across the hatch of a submarine 320m below the surface of the sea. assume the atmospheric pressure at the s...

question

Engineering, 13.09.2019 23:20

Increasing rake angle will decrease the tendency for built-up-edge to form. a) true b) false...

question

Engineering, 13.09.2019 23:20

An orthogonal cutting operation is performed using a rake angle of 15°, to=0.012 in and w=0.100 in. the chip thickness ratio is measured after the cut...

question

Engineering, 13.09.2019 23:20

Write the type of chips generated at each of the following cutting conditions, and explain why. a. low cutting speed: b. large depth of cut: c. very...

question

Engineering, 13.09.2019 23:20

How are the polymeric materials classified? give examples of the plastic materials and elastomers? give the difference between thermoplastics and t...

question

Engineering, 13.09.2019 23:20

What is components? what is phases? what is tie line?...

question

Engineering, 13.09.2019 23:20

Avariable speed reciprocating compressor of mass 400 kg has a natural frequency of 16.2 hz. (a) design an optimum auxiliary mass damper, so that the m...

question

Engineering, 13.09.2019 23:20

Specific cutting energy increases with increasing the cutting speed. a) true b) false...

question

Engineering, 13.09.2019 23:20

Two standard spur gears have a diametrical pitch of 10, a center distance 3.5 inches and a velocity ratio of 2.5. how many teeth are on each gear?...

question

Engineering, 13.09.2019 23:20

Consider a wind turbine subjected to 30 km/hr steady winds. if the turbine produces 480 kw of power and the velocity downstream of the wind turbine is...

question

Engineering, 13.09.2019 23:20

You are traveling in an airplane. the engineer who designed it is, casually, on your side. he tells you that the wings were designed using the von mis...

More questions: Mathematics Another questions

Questions on the website: 13722367