Physics, 05.11.2019 04:31 nemalmaqsoodp53nhh

An object is formed by attaching a uniform, thin rod with a mass of mr = 6.59 kg and length l = 5.24 m to a uniform sphere with mass ms = 32.95 kg and radius r = 1.31 m. note ms = 5mr and l = 4r. what is the moment of inertia of the object about an axis at the left end of the rod?

Answers: 1

Show answers

Answers

Answer from: shalynmincey

I = 188.5 Kg m²

Explanation:

The moment of inertia of your body is given by the relationship

I = ∫ r² dm

Since the mass and the squared distance are scalars the moment of inertia is additive, we just have to take into account from where they are measured.

In addition, we will use the parallel axes theorem, there is the moment of inertia for any axis to the center of mass, where we can consider mass as punctual

I = $I_{cm}$ + M D²

Our body is formed by two bodies: the rod and the sphere. Suppose the system is on the x axis

-Moment of inertia the rod, with an axis at one end

as the bar is uniform let's define a longitudinal mass density

λ = m / L = dm / dx

dm = λ dx

I = ∫ x² (λ dx) = λ ∫ x² dx

I = λ x³/3

We evaluate from the lower limit x = 0 to the upper limit x = L

I = λ (L³/3 -0)

Let's change the density for its value

I = M/L L³ / 3

$I_{r}$ = M L² / 3

-Moment of inertia of the sphere with respect to an axis at the end of the rod

In this case we will use the moment of inertia of the center of mass and then use the parallel axes theorem

$I_{cm}$ = 2/5 $M_{s}$ R²

The distance is the length of the rod

D = L

$I_{s}$ = 2/5 $M_{s}$ Rs2 + $M_{s}$ L2

Total inertia element is the sum of these two

I = $I_{r}$ + $I_{s}$

I = $M_{r}$ L² / 3 + 2/5 $M_{s}$ $R_{s}$ ² + $M_{s}$ L²

Let's replace and calculate

For our case

$M_{s}$ = 5 $M_{r}$

L = 4R

I = $M_{r}$ L² / 3 + 2/5 (5 $M_{r}$ ) (L/4)² 2 + (5 $M_{r}$ ) L²

I = $M_{r}$ L² (1/3 + 1/8 + 5)

I = $M_{r}$ L² (5,458)

I = 6.59 5.24 5.458

I = 188.5 Kg m²

Answer from: Quest

We can infer that star y is closer but other factors must be considered including the heat of the star, the mass, and the brightness of the star. even though star x seems dimmer it may just be less bright or contain less heat.

Answer from: Quest

Ai think hope that

Another question on Physics

Physics, 21.06.2019 15:40

Rosa records the distance that a toy car rolls and the time it takes to cover the distance. what scientific practice is this? collecting data asking a question providing explanations communicating results

Answers: 3

Answer

Physics, 21.06.2019 17:10

The dissociation energy of a molecule is the energy required tobreak apart the molecule into its separate atoms. the dissociationenergy for a particular molecule is 5.48 x 10-18 j.suppose that this energy is provided by a single photon. determinethe (a) wavelength and (b) frequency of the photon

Answers: 1

Answer

Physics, 22.06.2019 00:00

How do the measurements of charge at the different locations on the sphere compare to each other? the charge measurements are different at all locations on the sphere. the charge measurements are virtually not the same at all locations on the sphere except for the charge at the very top and at the very bottom that are equal. the charge measurements are virtually the same at all locations on the sphere except for the charge at the very top. at the top, the conductive sphere has a small disk that is made of different material. the charge measurements are the same at all locations on the sphere. what happens to the charge on the conductive sphere when it is connected to a source of charge such as the electrostatic voltage source? nothing will happen because no charge goes around the surface of the sphere. the charge on the conductive sphere spreads out over the surface of the sphere; being greater in some specific locations on the sphere. the charge on the conductive sphere spreads out uniformly over the surface of the sphere. the charge on the conductive sphere spreads out non-uniformly over the surface of the sphere.

Answers: 3

Answer

Physics, 22.06.2019 05:10

Total solidification times of three casting geometries are to be compared: a sphere, a cylinder, in which the length-to-diameter ration - 1.0, and a cube. volume = 1000 cm^3 for all three shhapes, and the same casting alloy is used. a) determine the solidification times of each geometry b) based on the results of part (a), which geometric element would make the best riser? c) if the mold constant = 3.5 min/cm^2 in chvorinov's rule, compute the total solidification time for each casting.

Answers: 3

Answer

You know the right answer?

An object is formed by attaching a uniform, thin rod with a mass of mr = 6.59 kg and length l = 5.24...

Questions