subject
Physics, 02.11.2020 19:40 Deascry

PLEASE HELP, WILL MARK BRAILIEST Questions
Section I: Experimental Overview
What is the purpose of the lab, the importance of the topic, and the question you are trying to answer?
What is your hypothesis (or hypotheses) for this experiment?
What methods are you using to test this (or each) hypothesis?
Section II: Data and Observations
Locate the data and observations collected in your lab guide. What are the key results? How would you best summarize the data to relate your findings?
Do you have quantitative data (numerical results or calculations)? Do you have qualitative data (written observations and descriptions)? How can you organize this date for your report?
Section III: Analysis and Discussion
What do the key results indicate?
If you constructed graphs, what trends do they indicate in your data?
Were there any problems with the experiment or the methods? Did you have any surprising results?
Section IV: Conclusions
What do the results tell you about your hypothesis(es)?
How do the data support your claim above?
If you could repeat the experiment and make it better, what would you do differently and why?
Writing the Lab Report
Now you will use your answers from the questions above to write your lab report. Follow the directions below.
Section I: Experimental Overview
Use your answers from questions 1–3 as the basis for the first section of your lab report. This section provides your reader with background information about why you conducted this experiment and how it was completed. Outline the steps of the procedure in full sentences. It also provides potential answers (your hypothesis/es) relative to what you expected the experiment to demonstrate. This section should be 1–3 paragraphs in length.
Section II: Data and Observations
Use your answers from questions 4–5 as the basis for the second section of your lab report. This section provides your reader with the data from the experiment, in a summarized and concise way. No paragraphs are required for this section, but you do need to include the key data and observations from which you will generate your analysis and discussion. This section is objective.
Section III: Analysis and Discussion
Use your answers from questions 6–8 as the basis for the third section of your lab report. This section provides your reader with your interpretation of the data set. You will also give an example of any calculations or formulas you used to analyze your data. Also, you will want to include any graphs that you made and interpret them for the reader.
If you did construct graphs, your Student Guide included information on which graphs to construct. Graphs should have the following:
Appropriate titles
Appropriate labels for each axis
Appropriate scales for each axis
Correct units for the data
Complete a rough sketch of each graph. Explain in one or two sentences what trend the reader should observe in each of your graphs.
Mention any problems, unusual or unexpected data, or other factors with the experiment here, and suggest possible causes. This section can be somewhat subjective, unlike Section II, because you are free to include your personal interpretations or even speculation if it adds constructive, reasonable insight to the discussion.
This section is variable in length, and should likely be the longest part of your report.
Section IV: Conclusions
Use your answers from questions 9-11 as the basis for the fourth section of your lab report. In this section you will summarize the outcome of the experiment, and discuss how the original hypothesis(es) was (were) either supported or refuted. Use logic and reason in explaining your statements, and be sure to refer to specific data from your experiment that supports your argument.
This section also demonstrates your understanding of the experiment, through your ability to offer constructive criticism about its design and make suggestions for future experimentation. There are always ways that experiments can be improved. Now that you are a veteran of this experiment and have experience with the procedure, offer some advice to the next scientist about what you suggest and why.

ansver
Answers: 3

Another question on Physics

question
Physics, 22.06.2019 00:30
Part f - example: finding two forces (part i) two dimensional dynamics often involves solving for two unknown quantities in two separate equations describing the total force. the block in (figure 1) has a mass m=10kg and is being pulled by a force f on a table with coefficient of static friction îľs=0.3. four forces act on it: the applied force f (directed î¸=30â above the horizontal). the force of gravity fg=mg (directly down, where g=9.8m/s2). the normal force n (directly up). the force of static friction fs (directly left, opposing any potential motion). if we want to find the size of the force necessary to just barely overcome static friction (in which case fs=îľsn), we use the condition that the sum of the forces in both directions must be 0. using some basic trigonometry, we can write this condition out for the forces in both the horizontal and vertical directions, respectively, as: fcosî¸â’îľsn=0 fsinî¸+nâ’mg=0 in order to find the magnitude of force f, we have to solve a system of two equations with both f and the normal force n unknown. use the methods we have learned to find an expression for f in terms of m, g, î¸, and îľs (no n).
Answers: 2
question
Physics, 22.06.2019 14:30
Aracecar driver has to hold on tightly when going around a banked curve. approximately what is the centripetal force on a 2220.0 kg car going around a circle with a diameter of 190.0 meters at 25.0 m/s?
Answers: 1
question
Physics, 22.06.2019 16:50
Calculate the first and second velocities of the car with four washers attached to the pulley, using the formulas v1 = 0.25 m / t1 , and v2 = 0.25 m / (t2 – t1) where t1 and t2 are the average times the car took to reach the 0.25 and the 0.50 meter marks. record these velocities, to two decimal places, in table e.
Answers: 2
question
Physics, 22.06.2019 17:00
Two conductors, a and b, are each in the shape of a tetrahedron. but of different sizes. they are charged in the following manner: 1. tetrahedron a is charged from an electrostatic generator to charge q. 2. tetrahedron a is briefly touched to tetrahedron b. 3. steps 1 and 2 are repeated until the charge on tetrahedron b reaches a maximum value. if the charge on tetrahedron b was q/4 after the first time it touched tetrahedron a. what is the final charge qbmax on tetrahedron b?
Answers: 2
You know the right answer?
PLEASE HELP, WILL MARK BRAILIEST Questions
Section I: Experimental Overview
What is the...
Questions
Questions on the website: 13722359