Asolution contains some or all of the ions cu2+,al3+, k+,ca2+, ba2+,pb2+, and nh4+. the following tests were performed, in order, on the solution.1. addition of 6 m hcl produced no reaction.2. addition of h2s with 0.2 m hcl produced a black solid.3. addition of (nh4)2s produced a white solid.4. addition of (nh4)2hpo4 in nh3 produced no reaction.5. the final supernatant when heated produced a purple flame. identify which of these ions were present in the solution (p), which were absent (a), and which were inconclusive (i)a. cu2+b. al3+c. k+d. ca2+e. ba2+f. pb2+g. nh4+

See below explanation

Explanation:

When having a mixture of metals in solution, you may perform an analytical study (using selective chemical conditions), that may help you to determine whether a metal (cation) is present or not

Using selective analytes (or conditions), leads to consecutive precipitations, until most of the cations are separated in precipitates

With this technique, you may identify metals in different groups, each group will have its analyte (or condition), which will help to have a different precipitate:

-Group I: Ag⁺, Pb⁺², Hg⁺²;  Analyte: HCL ; Precipitate: AgCl (white) , PbCl₂, HgCl₂

-Group II: As⁺³ , Bi⁺³, Cd⁺², Cu⁺² , Sb⁺³, Sn⁺² ; Analyte: H₂S (g) with HCL ; Precipitate: As₂S₃ , Bi₂S₃ , CdS (yellow) , CuS (black), Sb₂S₃, SnS

-Group III: Co⁺², Fe⁺², Fe⁺³, Mn⁺², Ni⁺², Zn⁺², Al⁺³, Cr⁺³; Analyte: NaOH or NH₃ with (NH₄)₂S (ac) ; Precipitate: CoS (black) , FeS, MnS , NiS (black), ZnS (white) , Al(OH)₃ (white), Cr(OH)₃  

-Group IV: Mg⁺², Ca⁺², Sr⁺², Ba⁺²; Analyte: Na₂CO₃ (ac) or (NH₄)₂HPO₄ (ac); Precipitate: respective carbonate or phosphate MgCO₃/MgHPO₄, CaCO₃/CaHPO₄ , SrCO₃/SrHPO₄, BaCO₃/BaHPO₄

-Group V: Li⁺, K⁺, Na⁺, Rb⁺, Cs⁺, NH₄⁺ ; will remain all in final solution

According to the original statement:

A solution contains one or more of the following: Cu⁺², Al⁺³, K⁺, Ca⁺², Ba⁺², Pb⁺², NH₄⁺

1)Addition on HCl 6M produces no change: we can say the sample does not contain Pb⁺² (group I)

2)Addition of H₂S with 0.2 M HCL produced a black solid: we could say sample contains Cu⁺²(group II)

3)Addition of (NH₄)₂HPO₄ in NH₃ produces no reaction: we could say we don´t have Ca⁺² and /or Ba⁺²  (group IV)

4)The final supernatant, when heated produced a purple flame: in the final solution, we have K⁺ (group V), which produces a purple flame (based on its characteristic emission spectrum when subjected to flame)

This analysis will be inconclusive for NH₄⁺ (according to above describe technique)

answer: the value of enthalpy change will be -152.80 kj.

solution:

pressure = 1atm , temperature = = 298 k

given that pressure and temperature are same in both gases , the number of moles of both gases can be determined by the ideal gas equation.

according to reaction 3 moles no are reacting with 1 mol of ,then 0.49 mol of no will react with moles of ozone that is 0.16 moles of ozone. since, no is limiting reagent and is an excessive reagent.

enthalpy change for the reaction between the given volumes of the gases is :