subject

Chemistry, 23.01.2022 22:20 jacobdesalvo8155

What is thermal energy? The kinetic energy or of atoms or that make up .

ansver

Answers: 1

Show answers

Another question on Chemistry

question

Chemistry, 22.06.2019 07:40

22. a flask containing 450 ml of 0.50 m h2so4 was accidentally knocked to the floor. how many grams of nahco, do you need to put on the spill to neutralize the acid according to the following equation: h2so4(aq)+2 nahcos(aq) na,so(aq) +2 h20()+2 co2(g) d) 38 g a) 2.3 g b) 9.5 g c) 19 g

Answers: 1

question

Chemistry, 22.06.2019 18:10

The atom fluorine generally will become stable through the formation of an ionic chemical compound by accepting electron(s) from another atom. this process will fill its outer energy level of electrons.

Answers: 1

question

Chemistry, 22.06.2019 22:30

The vapor pressure of ethanol is 1.00 × 102 mmhg at 34.90°c. what is its vapor pressure at 61.61°c? (δhvap for ethanol is 39.3 kj/mol.)

Answers: 2

question

Chemistry, 23.06.2019 01:30

Ascientist is measuring the pressure that is exerted by each of the following gases in the atmosphere: carbon dioxide, oxygen, and nitrogen. which term most likely describes what she is measuring?

Answers: 1

You know the right answer?

What is thermal energy? The kinetic energy or of atoms or that make up ....

Questions

question

Mathematics, 13.09.2019 23:20

When given a graph, the vertical line test can be used to determine functionality. describe the vertical line test and explain the reasons why a graph...

question

Engineering, 13.09.2019 23:20

Two factors that can be modified to optimize the cutting processes are feed and depth, and cutting velocity. a) true b) false...

question

Engineering, 13.09.2019 23:20

The highest cutting temperature is located close to the shear zone. a) true b) false...

question

Engineering, 13.09.2019 23:20

The largest source of heat generated in metal cutting is due to friction. a) true b) false...

question

Engineering, 13.09.2019 23:20

Calculate the differential pressure in kpa across the hatch of a submarine 320m below the surface of the sea. assume the atmospheric pressure at the s...

question

Engineering, 13.09.2019 23:20

Increasing rake angle will decrease the tendency for built-up-edge to form. a) true b) false...

question

Engineering, 13.09.2019 23:20

An orthogonal cutting operation is performed using a rake angle of 15°, to=0.012 in and w=0.100 in. the chip thickness ratio is measured after the cut...

question

Engineering, 13.09.2019 23:20

Write the type of chips generated at each of the following cutting conditions, and explain why. a. low cutting speed: b. large depth of cut: c. very...

question

Engineering, 13.09.2019 23:20

How are the polymeric materials classified? give examples of the plastic materials and elastomers? give the difference between thermoplastics and t...

question

Engineering, 13.09.2019 23:20

What is components? what is phases? what is tie line?...

question

Engineering, 13.09.2019 23:20

Avariable speed reciprocating compressor of mass 400 kg has a natural frequency of 16.2 hz. (a) design an optimum auxiliary mass damper, so that the m...

question

Engineering, 13.09.2019 23:20

Specific cutting energy increases with increasing the cutting speed. a) true b) false...

question

Engineering, 13.09.2019 23:20

Two standard spur gears have a diametrical pitch of 10, a center distance 3.5 inches and a velocity ratio of 2.5. how many teeth are on each gear?...

question

Engineering, 13.09.2019 23:20

Consider a wind turbine subjected to 30 km/hr steady winds. if the turbine produces 480 kw of power and the velocity downstream of the wind turbine is...

question

Engineering, 13.09.2019 23:20

You are traveling in an airplane. the engineer who designed it is, casually, on your side. he tells you that the wings were designed using the von mis...

question

Engineering, 13.09.2019 23:20

Cost of machining operations is primarily affected by tool life, power consumed and workpiece material. a) true b) false...

question

Engineering, 13.09.2019 23:20

What is the difference between "independent variables" and "dependent variables" in metal cutting operations? give three examples of each....

question

Engineering, 13.09.2019 23:20

Determine the molar air-fuel ratio for hydrogen (h2) burning with (a) 50% excess air and (b) 50% deficient air....

question

Engineering, 13.09.2019 23:20

Steam enters the high pressure turbine of a reheat cycle power plant at 3.5 mpa and 350and expands to 0.5 mpa after which it is reheated to 350°c. the...

question

Engineering, 13.09.2019 23:20

Aloan for $85,000 is to be paid in 10 yearly payments. each payment is larger by $100.00. compute the first, the fourth, and the last payment, if the...

More questions: Chemistry Another questions

Questions on the website: 13722367