Select the correct answer. Allan is manager of the software. His team has compiled various design documents prior to starting the development of the software. Allan wishes to have a design review, what advantage will a design review have?
A.
The design team learns how to present designs.
B.
The design can be altered.
C.
The design process can be changed.
D.
The design can be verified as per the client requirements.

When creating a presentation in libre office impress, where does the editing of slides take place? a. the slides panel b. the center panel c. the tasks panel, under the masters pages tab d. the tasks panel, under the layouts tab

Write a program that displays the following menu: geometry calculator 1. calculate the area of a circle 2. calculate the area of a rectangle 3. calculate the area of a triangle 4. quit enter your choice (1-4): if the user enters 1, the program should ask for the radius of the circle and then display its area. use the following formula: area = ď€(the square of r) use 3.14159 for ď€ and the radius of the circle for r. if the user enters 2, the program should ask for the length and width of the rectangle and then display the rectangle’s area. use the following formula: area = length * width if the user enters 3, the program should ask for the length of the triangle’s base and its height, and then display its area. use the following formula: area = base * height * .5 if the user enters 4, the program should end. input validation: display an error message if the user enters a number outside the range of 1 through 4 when selecting an item from the menu. do not accept negative values for the circle’s radius, the rectangle’s length or width, or the triangle’s base or height. note: if the user enters an improper menu choice (1-4), the program prints "the valid choices are 1 through 4. run the program again and select one of those." if the user enters a negative radius, the program prints "the radius can not be less than zero." if the user enters a negative value for height or base, the program prints "only enter positive values for base and height."

Write a program that reads in a series of lines of input character by character (using the library function the first line of the input contains an integer which specifies the number of remaining lines of input, each of which contains a floating point number. the integer value on the first line can be read with (the library function) but all of the following lines can only be read with each line, after the first, contains a single floating point value, with up to four digits before the decimal point, and up to four digits following the decimal point, but there is not necessarily a decimal point in each number; i.e., it may appear to be an integer, but the digits should be read by your program, and the number should be converted to a corresponding floating point number. for instance, suppose the following input: 5 3.1255 20.25 0.875 1921.50 31 the required output is: − each of the input floating point values, printed on a separate line with four digits of precision, using printf(); − on the last line of the output, the string “total: ” followed by the sum of the input values, printed with printf() to 4 digits of precision. for example, the total of the sample input given above is 1976.7505, so the required output for this input would be: 3.1255 20.2500 0.8750 1921.5000 31.0000 total: 1976.7505 do not concern yourself with small differences in the total due to rounding, as the grader will not deduct points for this. constraints: − you are not allowed to use arrays on this portion of the lab assignment. − there is no maximum number of lines allowable. it all depends upon the first value of input. since you aren’t saving anything, it doesn’t matter. − you can assume that input will not contain more than 4 digits before or after the decimal point. you do not need to error check for this condition. -you must use getchar() to read in the floating point values one character at a time (i.e. do not use -you must declare and use your floating point values as a double to minimize rounding errors. -only use printf() to output the floating point numbers and the total (do not use − be sure your directions to the user are clear so they are sure to enter the input data correctly.