Determine the force in each member of the truss (ab, bd,
ac, bc, cd, de, df, eg, ef, gf) and s...
![subject](/tpl/images/cats/User.png)
Engineering, 13.09.2019 19:30 darrell1168
Determine the force in each member of the truss (ab, bd,
ac, bc, cd, de, df, eg, ef, gf) and state if the members are in
tensionor compression. set p1 = 2 kn. p2 = 4 kn. at every letter
there isa pin connection.
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Different types of steels contain different elements that alter the characteristics of the steel. for each of the following elements, explain what the element does when alloyed with steel.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Slip occurs via two partial dislocations because of (a) the shorter path of the partial dislocation lines; (b) the lower energy state through partial dislocations; (c) the charge balance.
Answers: 1
You know the right answer?
Questions
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 14.12.2021 02:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/fizika.png)
Physics, 14.12.2021 02:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mir.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2021 02:10
![question](/tpl/images/cats/istoriya.png)
History, 14.12.2021 02:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 14.12.2021 02:10
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2021 02:10
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/User.png)