Engineering, 21.09.2019 02:10 beanokelley

Atank with some water in it begins to drain. the function v ( t ) = 46 − 3.5 t determines the volume of the water in the tank (in gallons) given a number of minutes t since the water began draining. what is the vertical intercept of f ? what does your answer to part (a) represent? select all that apply. the weight of the tank when it is empty. how many minutes it takes for all of the water to drain from the tank. the number of gallons of water in the tank when it starts draining. list all horizontal intercepts (or "roots") of f . what does your answer to part (b) represent? select all that apply. the weight of the tank when it is empty. the number of gallons of water in the tank when it starts draining. how many minutes it takes for all of the water to drain from the tank.

Answers: 3

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

What difference(s) did you notice using a pneumatic circuit over hydraulic circuit.explain why the pneumatic piston stumbles when it hits an obstacle.

Answers: 2

Answer

Engineering, 04.07.2019 18:20

A3-mm-thick panel of aluminum alloy (k 177 w/m-k, c 875 j/kg-k and ? = 2770 kg/m) is finished on both sides with an epoxy coating that must be cured at or above t,-150°c for at least 5 min. the production line for the curing operation involves two steps: (1) heating in a large oven with air at ts,0-175°c and a convection coefficient of h, 40 w/m2. k, and (2) cooling in a large chamber with air at 25°c and a con- vection coefficient of he 10 w/m2.k. the heating portion of the process is conducted over a time interval te which exceeds the ime required to reach 150°c by 5 min (h = r + 300 s). the coating has an emissivity of ? = 0.8, and the temperatures of the oven and chamber walls are 175 and 25°c, respectively. if the panel is placed in the oven at an initial temperature of 25°c and removed from the chamber at a safe-to-touch tempera ture of 37°c, what is the total elapsed time for the two-step curing operation?

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Along 8-cm diameter steam pipe whose external surface temperature is 900c connects two buildings. the pipe is exposed to ambient air at 70c with a wind speed of 50 km/hr blowing across the pipe. determine the heat loss from the pipe per unit length. (b) air at 500c enters a section of a rectangular duct (15 cm x 20 cm) at an average velocity of 7 m/s. if the walls of the duct are maintained at 100c. a) the length of the tube for an exit temperature of the air to be 40 0c. b)the rate of heat transfer from the air. c) the fan power needed to overcome the pressure drop in this section of the duct.

Answers: 1

Answer

Engineering, 04.07.2019 19:20

At steady state, air at 200 kpa, 325 k, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. the inlet cross-sectional area is 6 cm2. at the duct exit, the pressure of the air is 100 kpa and the velocity is 250 m/s. neglecting potential energy effects and modeling air as an 1.008 kj/kg k, determine ideal gas with constant cp = (a) the velocity of the air at the inlet, in m/s. (b) the temperature of the air at the exit, in k. (c) the exit cross-sectional area, in cm2

Answers: 2

Answer

You know the right answer?

Atank with some water in it begins to drain. the function v ( t ) = 46 − 3.5 t determines the volume...

Questions