Engineering, 26.09.2019 22:00 mfox793

Refrigerant 22 undergoes a constant-pressure process within a piston–cylinder assembly from saturated vapor at 3.5 bar to a final temperature of 25°c. kinetic and potential energy effects are negligible. evaluate the work and the heat transfer, each in kj per kg of refrigerant.

Answers: 3

Show answers

Answers

Answer from: clietmaster112

The work for the process at constant pressure is 3.1 kj/kg and Heat transfer is 23.42 kj/kg.

Explanation:

We have a process with Refrigerant 22, which is a constant pressure P = 3.5 bar. We have to find the thermodynamic properties of Refrigerant 22 in Thermodynamic tables.

According to the information presented in the problem, we can mention:

1 - Refrigerant is a closed system.

2- The process occurs at constant pressure

3- Work in this system will be a volume change mode.

4 - Variations for kinetic and potential energy are close to zero.

To calculate the work in kJ/kg, we should study the constant pressure process. As we only will consider volume change mode work, it will be calculated as follows:

$W_1_2 =\int\limits^2_1 {P} \, dV = P(V2 - V1)$

Values for V1 and V2 can be read from Thermodynamic tables for R-22.

As the initial condition is P=3.5 bar saturated vapor. We should search the properties at P = 3.5 bar using saturated R-22 Table (See Table A-7 Attached).

V1 is the specific volume for the initial condition, as it is satured vapor, V1 should be the specific volume for the gas phase in equilibrium.

$V1 = Vg (P=3.5 bar) = 0.0652 \frac{m^3}{kg}$

Final condition is the same pressure P=2.5 bar and T = 25°C. As Temperature is higher than Saturation Temperature at P = 2.5 bar. R-22 is superheated vapor. We can find the Volume (V2) in the table (See Table A-9 Attached).

$V2 = V (P = 3.5 bar ; T = 25 C) = 0.0776 \frac{m^3}{kg}$ .

After that, we can replace the equation for the work and convert to adequate units:

$W_1_2 = P (V2 - V1) = (2.5 bar) (0.0776 - 0.00652)\frac{m^3}{kg} \\W_1_2 = (2.5 bar) (0.0124)\frac{m^3}{kg} (\frac{1*10^5 N/m^2}{1 bar} ) (\frac{1 kJ}{1*10^3 Nm} ) = 3.1 \frac{kJ}{kg}$

The work for the process at constante pressure is 3.1 kj/kg.

The second part of the problem is to evaluate the heat transfer. We can use an energy balance, where Ek is kinetic energy, Ep is gravitational potential energy, U is internal energy, W is the work previously calculated and Q is the heat transfer.

ΔEk + ΔEp +ΔU =Q - W

Kinetic and potential variations are negligible. So: ΔEk = ΔEp = 0.

U2 - U1 = Q - W_1_2

Internal energies U2 and U1 are found in the table, as we did for the volume.

U1 = Ug (P=3.bar) = 223.02 kj/kg.

U2 = U (P = 3.5 bar ; T = 25 C) = 243.34 kj/kg.

Replacing we can calculate the heat transfer Q.

$Q = (U2 - U1) + W_1_2 = (243.34 - 223-02)\frac{kj}{kg} + 3.1 \frac{kj}{kg} \\Q= 23.42 \frac{kj}{kg}$

Heat transfer is 23.42 kj/kg.

Answer from: Quest

answer: 500 wph.

explanation:

Answer from: Quest

jesus loves you

explanation:

Another question on Engineering

Engineering, 03.07.2019 19:30

When using the ohmmeter function of a digital multimeter, the leads are placed in what position relative to the component being tested? a. parallel b. control c. series d. line

Answers: 3

Answer

Engineering, 04.07.2019 16:10

An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Courses that are developed by subject matter experts, internal or extemal to the college or university. these programs are marketed by the school (clo2) marks a)-vocational schools b)-vendor training c)-colleges & universities d)-continuing education programs

Answers: 2

Answer

You know the right answer?

Refrigerant 22 undergoes a constant-pressure process within a piston–cylinder assembly from saturate...

Questions