subject
Engineering, 01.10.2019 01:20 maria7515

A200 mw combined cycle gas turbine (ccgt) power generation station is considering the addition of a carbon capture and storage (ccs) system. the power generation station has a capacity factor of 90% and a heat rate of 8530 btu/kwh (higher heating value). the ccs system will remove and stores 85% of the co2 produced by the power generation station. however, the ccs system will reduce the efficiency of the plant by 6%. for example a plant with 32% efficiency without a ccs system would have 26% efficiency with a ccs system. the rated capacity of the plant will remain at 200 mw after the installation of the ccs. assume the natural gas used to fuel the ccgt power generation station is composed of 95% methane (ch4) and 5% nitrogen (n2) on a volumetric basis and has a higher heating value of 52.8 mj/kg. it is purchased for $3.50/mbtu. a. what is the mass fraction of carbon (c) in the natural gas (kg/kgna)? b. what is the co2 emission factor for the natural gas fuel (kgco2/mbtung)? c. what are the co2 emissions per mwh of electricity delivered for the current power generation station (mgco2/mwh)? d. what are the annual co2 emissions of the current generating station (mgcoz/y)? e. what would be the co2 emissions per mwh of electricity delivered if the ccs were installed (mgco2/mwh)? f. what would be the annual co2 emissions if the ccs is installed (mgooz/y)? g. how many metric tons of co2 emissions would be avoided annually if the ccs is installed (mg0oz/y)? h. what is the increased cost of fuel per year of electricity generated as a result of the ccs system (106 $/y)? i. what is the increased cost of fuel per metric ton of co2 avoided ($/mg002)?

ansver
Answers: 2

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
question
Engineering, 04.07.2019 18:10
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
question
Engineering, 04.07.2019 18:10
Thermal stresses are developed in a metal when its a) initial temperature is changed b) final temperature is changed c) density is changed d) thermal deformation is prevented e) expansion is prevented f) contraction is prevented
Answers: 2
question
Engineering, 04.07.2019 18:20
An engine runs on the ideal diesel cycle. the cycle has a compression ratio of 20 and a cutoff ratio of 2. the highest temperature in the cycle is 1200 k. if the heat into the system is 300 kj/kg of working fluid and using variable specific heats determine the work produced per mass of working fluid
Answers: 3
You know the right answer?
A200 mw combined cycle gas turbine (ccgt) power generation station is considering the addition of a...
Questions
question
History, 15.11.2019 05:31
question
History, 15.11.2019 05:31
question
Mathematics, 15.11.2019 05:31
question
Mathematics, 15.11.2019 05:31
question
Mathematics, 15.11.2019 05:31
Questions on the website: 13722359