Engineering, 03.10.2019 02:00 Briii582

Avertical piston-cylinder device initially contains 0.1 m3 of air at 400 k and 100 kpa. at this initial condition, the piston is resting on a stop. the piston-cylinder device is connected to a supply line with air at 400 k and a pressure of 500 kpa. the valve between the supply line and the piston-cylinder device is opened and is left open until the pressure in the piston-cylinder device reaches 500 kpa. the piston is observed to start moving when the pressure in the cylinder is 200 kpa and the piston continues to rise until it reaches a second stop. at the second stop, the piston-cylinder volume is 0.2 m3 . the final temperature and pressure in the piston-cylinder device are 440 k and 500 kpa, respectively. molecular weight of air = 28.97 kg/kmol. determine heat transfer (kj) during the entire process. indicate whether it is into the system or out of the system.

Answers: 1

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°c with a volumetric flow rate of 0.18 m3/s. refrigerant exits at 9 bar, 70°c. changes in kinetic and potential energy from inlet to exit can be ignored. determine the volumetric flow rate at the exit, in m3/s, and the compressor power, in kw.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater

Answers: 3

Answer

You know the right answer?

Avertical piston-cylinder device initially contains 0.1 m3 of air at 400 k and 100 kpa. at this init...

Questions