![subject](/tpl/images/cats/User.png)
Engineering, 11.10.2019 04:20 nimclean
Consider a 10.0 m long pipe, of diameter 0.6m, wall thickness 0.7 m, and a thermal conductivity k = 2.5 w/m k. the inside of the pipe is maintained at a constant temperature of 500°k while it is subjected to a constant external wall temperature of 100 °k. evaluate (a) the temperature profile within the pipe wall, and (b) the total heat transfer rate leaving at the pipe outer surface.
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Coiled springs ought to be very strong and stiff. si3n4 is a strong, stiff material. would you select this material for a spring? explain.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
You know the right answer?
Consider a 10.0 m long pipe, of diameter 0.6m, wall thickness 0.7 m, and a thermal conductivity k =...
Questions
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 18.04.2021 18:00
![question](/tpl/images/cats/istoriya.png)
History, 18.04.2021 18:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 18.04.2021 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 18.04.2021 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 18.04.2021 18:00
![question](/tpl/images/cats/en.png)
English, 18.04.2021 18:00
![question](/tpl/images/cats/en.png)
English, 18.04.2021 18:00
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/mkx.png)
Arts, 18.04.2021 18:00
![question](/tpl/images/cats/en.png)
English, 18.04.2021 18:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 18.04.2021 18:00
![question](/tpl/images/cats/ekonomika.png)
Business, 18.04.2021 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 18.04.2021 18:00
![question](/tpl/images/cats/en.png)
English, 18.04.2021 18:00
![question](/tpl/images/cats/en.png)
English, 18.04.2021 18:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 18.04.2021 18:00
![question](/tpl/images/cats/health.png)