Ihave these components:
- 40 rooms
- guard house
- speaker system
- high al...
Engineering, 11.10.2019 06:20 JuanTorres7
Ihave these components:
- 40 rooms
- guard house
- speaker system
- high alert indicator
- mild alert indicator - in use indicator
i was given these function of the components:
a) the intercom must have a connection from the gate to each room and from each room to another room. to reduce cable runs and minimise cost, a single cat5 cable runs from the room to a central switch in the building. another cable runs from the switch to the gate. this is shown in figure 1 below.
b) connection is establish by entering the room number into the keypad following by some call button. the room number is translated into a unique binary address embedded in the system.
c) when a room is called the buzzer is sounded and a visual indicator blinks on panel in the room.
d) if the call is accepted and the line is busy, all other terminals will have the in use indicator lit.
e) each alert indicator must have a unique code. these function is only activated by the college manager to all connected device. when alert is high, the buzzer must also ring for 30 seconds.
i am confused about drawing a flow chart giving the input conditions and discuss the process for room 5 on the intercom with the gate.
, any idea or close to my question is very much appreciated.
Answers: 2
Engineering, 03.07.2019 14:10
If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.
Answers: 3
Engineering, 04.07.2019 18:10
Apipe with an outside diameter of 15 cm is exposed to an ambient air and surrounding temperature of -20°c. the pipe has an outer surface temperature of 65°c and an emissivity of 0.85. if the rate of heat loss from the pipe surface is 0.95 kw per meter of length, the external convective heat transfer coefficient (h) is: (a) 12.5 w/m"k (b) 18.6 w/mk (c) 23.7 w/mk (d) 27.9 w/mk (e) 33.5 w/mk
Answers: 1
Engineering, 04.07.2019 18:20
Most leaks in reciprocating air compressors can be detected and minimized by: (clo4) a)-detecting leakage areas using ultrasonic acoustic detector. b)-tightening joints and connections c)-replacing faulty equipment d)-all of the given options
Answers: 2
Engineering, 06.07.2019 02:30
Around steel bar, made from material with a yield stress of 750mpa, is loaded so that it has stresses co locations of maximum normal stress and maximum shear stress. use maximum shear stress and maximum distortion energy theories to calculate the safety factors for initial yielding failures.
Answers: 3
Social Studies, 14.09.2020 23:01
Social Studies, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Computers and Technology, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Social Studies, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Social Studies, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01
English, 14.09.2020 23:01
English, 14.09.2020 23:01
Social Studies, 14.09.2020 23:01
Mathematics, 14.09.2020 23:01