subject
Engineering, 03.03.2020 18:10 pbargy9551

Fix the code so the program will run correctly for MAXCHEESE values of 0 to 20 (inclusive). Note that the value of MAXCHEESE is set by changing the value in the code itself. If you are not sure of how it should work then look at the Sample Runs of the next part. This part handles the beginning where it lists all the cheese types available and their prices. Note: it is a very simple fix that needs to be added to all the statements that have an array access.

ansver
Answers: 2

Another question on Engineering

question
Engineering, 06.07.2019 03:10
Asolid steel sphere (k=63.9 w m-1 k-1 , ? =7832 kg m-3 , c=0.523 kj kg-1 k-1 ), 100 mm in diameter is initially at a uniform temperature of 500o c and is suddenly quenched in a large oil bath for which t? = 100o c and h = 3200 w m-2 k-1. estimate the time required for the sphere to cool to 200o c and to 110o c
Answers: 1
question
Engineering, 06.07.2019 03:20
1kg of water contained in a piston-cylinder assembly undergoes two processes in series from an initial state where the pressure is 3.0 bar and the temperature is 150°c process 1-2: the water is compressed isothermally to a volume of 0.25 m^3 with 120 kj of work being done to the system. process 2-3: the water is heated at constant volume to a final pressure of 10 bar. a. find the change in internal energy for the system. b. calculate the amount of heat transferred, in kj. c. sketch both processes on a t-v diagram. (196.33 kj/kg, 76.33 kj)
Answers: 1
question
Engineering, 06.07.2019 04:10
Steam enters a converging-diverging nozzle at 1.0 mpa and 500°c with a negligible velocity at a mass flow rate of 2.5 kg/s, and it exits at a pressure of 200 kpa. assuming the flow through the nozzle to be isentropic, determine: the exit area and (a) (b) the exit mach number
Answers: 2
question
Engineering, 06.07.2019 04:10
An array of m-50 thermoelectric modules is installed on the exhaust of a sports car. each module has an effective seebeck coefficient of sp of 0.143 5vk and an internal electrical resistance of r.-4 ? in addition, : (15 points each module is of width w 60mm and contains n=100 pairs of semiconducting pellets. each pellet hasan overall length of 2l-5mm and a cross-sectional area as 1.2 x 10'm and is characterized by a thermal conductivity of kpl2w rnk. the hot side of each module is exposed to exhaust gases at·p650c with hia4ow rrk while the osite side of each module is cooled by pressurized water at surface) and 156 °c (at the cool surface). 11s c with h: -500w/m'k. the modules are wired n series and the load resistance is r d=400ohm .the module surface temperatures, t, and ts are 183 "c (at the hot surface and 156c (at the cool surface) a)-draw a schematic of this scenario and label all parts. a. b. if the induced current, i, is 0.15 amps, what is the total power (pa) for one module? c. what is the total power harvest from the exhaust with all 50 modules?
Answers: 2
You know the right answer?
Fix the code so the program will run correctly for MAXCHEESE values of 0 to 20 (inclusive). Note tha...
Questions
question
Arts, 18.04.2020 00:40
question
History, 18.04.2020 00:40
Questions on the website: 13722363