3 sensors are attached to a printing
device with three alarms attached to
the sensors. The...
![subject](/tpl/images/cats/User.png)
Engineering, 11.03.2020 02:49 jsmn9083
3 sensors are attached to a printing
device with three alarms attached to
the sensors. The first sensor A detects
if the device needs ink
the second sensor B detects if the
device needs repairs. The third sensor
C, delects of the device jams.
An alarm sounds of two or more or
more problems occur
(1) device a truth table for the system
2) Write an SOP expression for the
system & minimize it.
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Condition monitoring is a major component of. (clo4) a)- predictive maintenance. b)-preventive maintenance c)-proactive maintenance d)-reactive maintenance.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200Β°c and outer surface temperature of the insulation to be 15Β°c. calculate the thickness of insulation required.
Answers: 3
You know the right answer?
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.07.2019 22:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/fizika.png)
Physics, 17.07.2019 22:30
![question](/tpl/images/cats/biologiya.png)
Biology, 17.07.2019 22:30
![question](/tpl/images/cats/mat.png)
Mathematics, 17.07.2019 22:30
![question](/tpl/images/cats/istoriya.png)
History, 17.07.2019 22:30
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
History, 17.07.2019 22:30
![question](/tpl/images/cats/mat.png)
Mathematics, 17.07.2019 22:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.07.2019 22:30
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 17.07.2019 22:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 17.07.2019 22:30