Engineering, 11.03.2020 22:58 only1123
Air flows steadily through a turbine that produces 3.5x 105 ft-lbf/s of work. Using the data below at the inlet and outlet, where the inlet is 10 feet below the outlet, please calculate the heat transferred in units of BTU/hr. You may assume steady flow and ignore viscous work.
Answers: 1
.
, shaft work rate is 
, rate of accumulation of energy inside control volume is 
, rate of work accomplished in viscous effects at the surface is 
, and the net energy efflux from the control volume is 
![\begin{array}{l}\frac{\delta Q}{d t}-\frac{\delta W_{s}}{d t}=\rho v A\left[e+\frac{P}{\rho}\right]_{2}-\rho v A\left[e+\frac{P}{\rho}\right] \\=\rho_{1} Q\left[u_{2}-u_{1}+\frac{v_{2}^{2}-v_{1}^{2}}{2}+\left(P_{2} / \rho_{2}-P_{1} / \rho_{1}\right)+g\left(z_{2}-z_{1}\right)\right] \\=\rho_{1} A_{1} v_{1}\left[u_{2}-u_{1}+\frac{v_{2}^{2}-v_{1}^{2}}{2}+\left(P_{2} / \rho_{2}-P_{1} / \rho_{1}\right)+g\left(z_{2}-z_{1}\right)\right]\end{array}](/tpl/images/0543/5935/d37d2.png)
internal energy at exit section is 
volumetric flow rate is Q, inlet fluid density is 
, outlet fluid density is 
, specific energy is e, exit velocity is 
, inlet velocity is 
, inlet pressure is 
, outlet pressure is 
, acceleration due to gravity is g and distance between inlet and outlet is z.
![\frac{\delta Q}{d t}-\frac{\delta W_{s}}{d t}=\rho_{1} A_{1} v_{1}\left[u_{2}-u_{1}+\frac{v_{2}^{2}-v_{1}^{2}}{2}+\left(P_{2} / \rho_{2}-P_{1} / \rho_{1}\right)+g\left(z_{2}-z_{1}\right)\right]](/tpl/images/0543/5935/54105.png)
![\begin{aligned}&\frac{\delta Q}{d t}=\left(9.98 \times 10^{5}+3.5 \times 10^{5}\right) \mathrm{ftlb}_{\mathrm{f}} / \mathrm{s}\\&=13.48 \times 10^{5} \mathrm{ftb}_{\mathrm{f}} / \mathrm{s}\left[\frac{1 \mathrm{Ba}}{778.17 \mathrm{ftbr}}\right]\left[\frac{3600 \mathrm{s}}{1 \mathrm{hr}}\right]\\&=6.23 \times 10^{6} \mathrm{Btu} / \mathrm{hr}\end{aligned}](/tpl/images/0543/5935/32b1b.png)
.
Another question on Engineering
Engineering, 04.07.2019 18:10
Assuming compressible flow of air and that the measurements are done at flagstaff a pitot static tube that gives the difference of total and static pressure measures 0.35 m of mercury. what is the velocity of air? assume the temperature to be 300k. (submit your excel or matlab calculation sheet)
Answers: 1
Engineering, 04.07.2019 18:20
Derive the correction factor formula for conical nozzle i=-(1+ cosa) and calculate the nozzle angle correction factor for a nozzle whose divergence hal-fangle is 13 (hint: assume that all the mass flow originates at the apex of the cone.
Answers: 3
Engineering, 04.07.2019 18:20
Along 8-cm diameter steam pipe whose external surface temperature is 900c connects two buildings. the pipe is exposed to ambient air at 70c with a wind speed of 50 km/hr blowing across the pipe. determine the heat loss from the pipe per unit length. (b) air at 500c enters a section of a rectangular duct (15 cm x 20 cm) at an average velocity of 7 m/s. if the walls of the duct are maintained at 100c. a) the length of the tube for an exit temperature of the air to be 40 0c. b)the rate of heat transfer from the air. c) the fan power needed to overcome the pressure drop in this section of the duct.
Answers: 1
Engineering, 04.07.2019 19:10
In general, how do thermosetting plastics compare to thermoplastics in mechanical and physical properties?
Answers: 3
You know the right answer?
Air flows steadily through a turbine that produces 3.5x 105 ft-lbf/s of work. Using the data below a...
Questions
Mathematics, 07.10.2019 07:10
Business, 07.10.2019 07:10
Mathematics, 07.10.2019 07:10
History, 07.10.2019 07:10
English, 07.10.2019 07:10
Mathematics, 07.10.2019 07:10
History, 07.10.2019 07:10
History, 07.10.2019 07:10
Chemistry, 07.10.2019 07:10
Mathematics, 07.10.2019 07:10
