![subject](/tpl/images/cats/User.png)
Engineering, 14.03.2020 00:55 olorteguimikie
Rain is falling on a poorly designed 150-m^2 flat roof of a contemporary home. The design flaw requires the water level on the roof to reach approximately 5 cm above the plane of the roof before the water flows into drains.
a. Taking the accumulated rain on the roof as the system, can the process before the water level reaches 5 cm be considered batch, semi-batch, or continuous? Is it transient or steady-state? Once the water starts to flow into the drains, how do your answers change?
b. Before the water starts draining, which of the terms in the general balance equation (Equation 4.2-1) can be omitted? Why? How do your responses change after water starts draining?
c. Water begins flowing from the roof after 30 minutes of rainfall. What will the rate of draining (L/s) be if rain continues to fall at the same rate?
d. The home owner is considering installation of a "green" roof that is partially or completely covered with vegetation. If this is done, how would your answers to Parts a and b change? List at least two concerns and two environmental benefits of the new roof.
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Burgers vector is generally parallel to the dislocation line. a)-true b)-false
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which of the following components of a pid controlled accumulates the error over time and responds to system error after the error has been accumulated? a)- proportional b)- derivative c)- integral d)- on/off.
Answers: 2
You know the right answer?
Rain is falling on a poorly designed 150-m^2 flat roof of a contemporary home. The design flaw requi...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 01.08.2019 08:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 01.08.2019 08:30
![question](/tpl/images/cats/en.png)
English, 01.08.2019 08:30
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 01.08.2019 08:30
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/es.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/ekonomika.png)
Business, 01.08.2019 08:30