![subject](/tpl/images/cats/User.png)
Engineering, 30.03.2020 21:00 sswaqqin
Design a full-wave bridge rectifier to supply 12V DC voltage to a resistive load of RL=3Ω at the output, assuming an AC supply with 60 Hz frequency with the following characteristics: a) Unfiltered (without output capacitor) b) Filtered. Design a filter capacitor so that the ripple factor of the output voltage is less than %5. Regularly if you add a filter capacitor, the average output voltage would increase. You should revise the AC supply peak voltage VVmm calculated in (a) to match the average 12V DC requirement. Find and report the final value of VV�
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
When at a point two solid phase changes to one solid phase on cooling then it is known as a) eutectoid point b) eutectic point c) peritectic point d) peritectoid point
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Thermal stresses are developed in a metal when its a) initial temperature is changed b) final temperature is changed c) density is changed d) thermal deformation is prevented e) expansion is prevented f) contraction is prevented
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
An open feedwater heater operates at steady state with liquid entering at inlet 1 with t? = 40°c and pl = 1 .2 mpa. water vapor att2-200°c and p2 = 1.2 mpa enters at inlet 2. saturated liquid water exits with a pressure of pa 1.2 mpa. neglect heat transfer with the surroundings and all kinetic and potential energy effects, determine the mass flow rate of steam at inlet 2 if the mass flow rate of liquid water at inlet 1 is given as 2 kg/s.
Answers: 3
You know the right answer?
Design a full-wave bridge rectifier to supply 12V DC voltage to a resistive load of RL=3Ω at the out...
Questions
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/fizika.png)
Physics, 20.07.2019 14:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 20.07.2019 14:50
![question](/tpl/images/cats/biologiya.png)
Biology, 20.07.2019 14:50
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 20.07.2019 14:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/fizika.png)
Physics, 20.07.2019 14:50
![question](/tpl/images/cats/ekonomika.png)
Business, 20.07.2019 14:50