Engineering, 14.04.2020 23:47 Dreynolds1667

Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220 °C flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3 m/s.
If the flat plate surface temperature is maintained at 80 °C, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.

Answers: 2

Show answers

Answers

The local convection heat transfer coefficient at 1 m from the leading edge is $0.44 \frac{W}{m^{2} \times K}$ , the average convection heat transfer coefficient over the entire plate is $0.293 \frac{W}{m^{2} \times K}$ and the total heat flux transfer to the plate is 61.6 KJ .

Explanation:

It is case of heat and mass transfer in which due to temperature difference between gas and surface. Further temperature boundary layer will developed on flat plate in longitudinal direction.

Hot carbon dioxide exhaust gas

physical properties

$r= 1.05 \frac{kg}{m^{3}}$

$c_p = 1.02 \frac{kJ}{Kg \times K}$

$m= 231 \times 10^{7} \frac{N \times s }{m^2}$

υ = $21.8 \times 10^{6} \frac{m^2}{s}$

$k = 32.5 \times 10^{3} \frac{W}{m \times K}$

$\alpha = 30.1 \times 10^{6} \frac{m^{2}}{s}$

Pr = 0.725

Apart from these other data arr given below,

$v= 3 \frac{m}{s} \\ p= 1 atm \\ L_c = 1.5m \\T_g= 220 C \\ T_s = 80 C$

To find the local convection heat transfer coefficient at 1 m from the leading edge, we use correlation used for laminar flow over flat plate,

$Nu = \frac{ h \times L }{k} = 0.332 \times (Re^{\frac{1}{2} }) \times (Pr^{\frac{1}{3} })$

where h= Average heat transfer coefficient

L= Length of a plate

k= Thermal Conductivity of carbon dioxide

Re = Reynold's Number

Pr = Prandtle Number

(a) Convection heat transfer coefficient at 1 m from the leading edge

is referred as local convection heat transfer coefficient.

To find convection heat transfer coefficient at 1 m from leading edge,

$Nu = \frac{ h_local \times L }{k} = 0.332 \times (Re^{\frac{1}{2} }) \times (Pr^{\frac{1}{3} })$

Here, first we have to find Re and Pr,

$Re = \frac{r \times v \times L}{m}$

$Re = \frac{1.0594 \times 3 \times 1}{231 \times 10^{7}}$

$Re = 20.63 \times 10^{-10}$

Pr number is take from physical property data and Pr is 0.725.

Putting value of Re and Pr in main equation,

we get

$Nu = \frac{ h_local \times 1 }{32.5 \times 10^{3}} = 0.332 \times ( (20.63 \times 10^{-10})^{\frac{1}{2} }) \times (0.725^{\frac{1}{3} })$

$h_local = 32.5 \times 10^{3} \times 0.332 \times ( (20.63 \times 10^{-10})^{\frac{1}{2} }) \times (0.725^{\frac{1}{3} })$

$h_local = 0.44 \frac{W}{m^{2} \times K}$

(b) To find average convection heat transfer coefficient,

it can be find out as case (a), only difference is that instead of L=1 m, L=1.5 m would come,

Therefore,

$Nu = \frac{ h \times 1.5 }{32.5 \times 10^{3}} = 0.332 \times ( (20.63 \times 10^{-10})^{\frac{1}{2} }) \times (0.725^{\frac{1}{3} })$

Finally,

$h = \frac{0.44}{1.5}$

$h = 0.293 \frac{W}{m^{2} \times K}$

$Q = h \times (T_g - T_s)$

$Q = 0.293 \times (220-80) \\ Q= 0.293 \times 140 \\ Q= 61.6 KJ$

Answer from: Quest

unlike the threaded fasteners which are used to clamp the machine members, power screws are used to transmit power. common applications of power screws are: screw jacks: to lift weight. lead screw of lathe: for axial movement of tool and its precise positioning.

Answer from: Quest

answer:

can you answer my question?

explanation:

Another question on Engineering

Engineering, 03.07.2019 14:10

If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Assuming compressible flow of air and that the measurements are done at flagstaff a pitot static tube that gives the difference of total and static pressure measures 0.35 m of mercury. what is the velocity of air? assume the temperature to be 300k. (submit your excel or matlab calculation sheet)

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Which of the following controllers anticipates the future from the slope of errors over time? a)-proportional b)-on/off c)-integral d)-derivative.

Answers: 2

Answer

You know the right answer?

Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220 °C flows in p...

Questions