subject
Engineering, 25.04.2020 01:36 delmi02bazidera

The Blue Ox Tannery has asked you to assist them in preparations to file for a NPDES permit to discharge wastewater into the Zmellsbad River. The DNR water quality criterion for the Zmellsbad River is 5.00 mg/L of DO. They have asked you the following questions: What is the critical DO and where (at what distance) downstream does it occur? They have provided you with the following data. They pertain to the 7-year, 10-day low flow at the tannery.

Parameter Blue Ox wastewater Zmellsbad River
Flow, m3/s 1.148 7.222
GODS at 15°C, mg/L 90.00 N/A
ROD. at 15°C. mg/L N/A 7.66
DO. mg/L 1.00 6.00
Temperature. °C 15.0 15.0
k at 20°C. d-I 0.3685 NA
Speed. m/s N/A 0.300
Depth. m N/A 2.92
Bed-activity coefficient N/A 0.100

ansver
Answers: 1

Another question on Engineering

question
Engineering, 03.07.2019 14:10
Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.
Answers: 3
question
Engineering, 04.07.2019 18:10
Water at 55c flows across a flat plate whose surface temperature is held constant at 95c. if the temperature gradient at the plate's surface for a given value of x is 18 c/mm, find a) local heat transfer coefficient. b) heat flux
Answers: 3
question
Engineering, 04.07.2019 18:10
Hydraulic fluid with a sg. of 0.78 is flowing through a 1.5 in. i.d. pipe at 58 gal/min. the fluid has an absolute viscosity of 11.8 x 105 lbf-sec/ft2. is the flow laminar, turbulent or within the critical range? give both a numerical reynolds number and a term answer.
Answers: 3
question
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
The Blue Ox Tannery has asked you to assist them in preparations to file for a NPDES permit to disch...
Questions
question
Geography, 30.08.2019 23:00
question
Mathematics, 30.08.2019 23:00
question
Geography, 30.08.2019 23:00
Questions on the website: 13722359