Engineering, 25.04.2020 02:59 anyar

A NC drill press is to perform a series of through-hole drilling operations on a 1.75 in thick aluminum plate that is a component in a heat exchanger. Each hole is 3/4 in diameter. There are 100 holes in all, arranged in a 10 by 10 matrix pattern, and the distance between adjacent hole centers (along the square) = 1.5 in. The cutting speed = 300 ft/min, the penetration feed (z-direction) = 0.015 in/rev, and the traverse rate between holes (x-y plane) = 15.0 in/min. Assume that x-y moves are made at a distance of 0.50 in above the work surface, and that this distance must be included in the penetration feed rate for each hole. Also, the rate at which the drill is retracted from each hole is twice the penetration feed rate. The drill has a point angle = 100°. Determine the time required from the beginning of the first hole to the completion of the last hole, assuming the most efficient drilling sequence will be used to accomplish the job.

Answers: 1

Show answers

Answers

Answer from: rireneb

The total time required is $T_{total}= 1601 sec$

Explanation:

From the question we are told that the

The thickness of the aluminium plate is $t = 1.75 \ in$

The diameter of the holes is $d = \frac{3}{4} \ in$

The number holes is n = 100

The pattern they arranged is = 10 by 10 matrix

The distance between the adjacent holes is $D = 1.5 \ in$

The cutting speed $v = 300 \ ft/min =300 *12 = 3600 \ in /min$

The penetration feed is $P = 0.015 \ in / rev$

The traverse rate is $T_r = 15.0 \ in /min$

The distance of the x-y moves $L = 0.50 \ in$

The rate at which the drill id retracted is R = 2P

The point angle of the drill is $\theta = 100^o$

Generally the cutting speed is mathematically represented as

$v = \pi d N$

Where N is the rotational speed

Substituting values

$3600 = \pi * \frac{3}{4} N$

=> $N = \frac{3600}{0.75 * 3.142 }$

$N = 1527.68 rev /min = \frac{1527.68}{60} = 25.46 \ rev /sec$

Now the feed rate is mathematically represented as

$Feed \ Rate [F] = P * N$

Substituting values

F = 0.015 * 25.46

$= 0.3819 \ in$

Next is to obtain the approach distance

The approach distance is mathematically represented as

$a = 0.5 * d * tan (90 - \frac{\theta }{2} )$

substituting values

$a = 0.5 * 0.75 * tan ({90 - \frac{100}{2} })$

$a = 2.5646 \ in$

also we are told that the drill x-y moves is 0.5 in above the work surface

Then the when retracting the drill the total distance moves is

Hence the total drill distance is w = 0.5 + 1.75 + 0.3146

$= 2.5646 \ in$

The time required to drill on hole is

$t_1 = \frac{w }{F }$

Substituting values

$t_1 = \frac{2.56446}{0.3819}$

= 6.71 sce

The retracting rate of the drill would be

K = 2P N

R = 0.015 * 2 * 25.46

= 0.7638

The time required to move the drill out of one hole is

$t_ 2 = \frac{w}{K}$

Substituting value

$t_2 = \frac{2.5646}{0.7638}$

$= 3.3576 \ sec$

The time required to move from one hole to another is

$t_3 = \frac{D}{T_r}$

$= \frac{1.5}{0.25}$

$= 6 \ sec$

The time it would take to perform the drilling of 100 holes is mathematically represented as

t_4 = 100 *t_1

= 6.71 *100

$= 671 \ sec$

Time required for retracting the drill from 100 holes is mathematically represented as

t_5 = 100 * t_2

t_5 = 3.3576 *100

= 336 sec

The time taken to move through the 100 holes is

t_6 = number of travers time * t_3

The number of trans verse time is = 99

t_6 = 99 * 6

$= 594 \ sec$

The time required the drilling task from the beginning of the first hole to the hole is

$T_{total } = t_4 + t_5 + t_6$

= 671 + 336 + 594

$T_{total}= 1601 sec$

Answer from: Quest

Diene d fbfjcnfd ebjjn

Answer from: Quest

answer:

rawr

explanation:

Another question on Engineering

Engineering, 03.07.2019 19:30

When using the ohmmeter function of a digital multimeter, the leads are placed in what position relative to the component being tested? a. parallel b. control c. series d. line

Answers: 3

Answer

Engineering, 04.07.2019 18:20

Most leaks in reciprocating air compressors can be detected and minimized by: (clo4) a)-detecting leakage areas using ultrasonic acoustic detector. b)-tightening joints and connections c)-replacing faulty equipment d)-all of the given options

Answers: 2

Answer

Engineering, 04.07.2019 19:10

Asteam is contained in a rigid tank with a volume of 1 m3. initially, the pressure and temperature are 7 bar and 500 oc, respectively. the temperature drops due to cooling process. determine: (1) the temperature at which condensation begins in °c, (2) the fraction of the total mass that has condensed when the pressure decreased to 0.5 bar. (3) the volume in m3 occupied by saturated liquid at the final state?

Answers: 3

Answer

Engineering, 04.07.2019 19:10

What is the major difference between thermoplastics and thermosetting plastics from the polymerization structure point of view?

Answers: 2

Answer

You know the right answer?

A NC drill press is to perform a series of through-hole drilling operations on a 1.75 in thick alumi...

Questions