Engineering, 21.05.2020 05:00 ramandeep

A double-pipe heat exchanger is used to cool a hot fluid (cp = 3800 J/kg·K) entering the heat exchanger at 200°C with a flow rate of 0.4 kg/s. In the cold side, cooling fluid (cp = 4200 J/kg·K) enters the heat exchanger at 10°C with a mass flow rate of 0.5 kg/s. The double-pipe heat exchanger has a thin-walled inner tube, with convection heat transfer coefficients inside and outside of the inner tube estimated to be 1400 W/m2 ·K and 1100 W/m2 ·K, respectively. The heat exchanger has a heat transfer surface area of 2.5 m2 , and the estimated fouling factor caused by the accumulation of deposit on the surfaces is 0.0002 m2 ·K/W. (a) Determine the effectiveness values for the parallel- and counter-flow configurations. (b) Determine outlet temperatures of the hot fluid for the parallel- and counter-flow configurations. (c) Determine outlet temperatures of the cold fluid for the parallel- and counter-flow configurations.

Answers: 2

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 03.07.2019 15:10

Apiston-cylinder with a volume of 0.25 m3 holds 1 kg of air (r 0.287 k/kgk) at a temperature of 100 c. heat transfer to the cylinder causes an isothermal expansion of the piston until the volume triples. how much heat is added to the piston-cylinder?

Answers: 3

Answer

Engineering, 03.07.2019 15:10

Heat is added to a piston-cylinder device filled with 2 kg of air to raise its temperature 400 c from an initial temperature of t1 27 cand pressure of pi 1 mpa. the process is isobaric process. find a)-the final pressure p2 b)-the heat transfer to the air.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?

Answers: 1

Answer

You know the right answer?

A double-pipe heat exchanger is used to cool a hot fluid (cp = 3800 J/kg·K) entering the heat exchan...

Questions