![subject](/tpl/images/cats/User.png)
Engineering, 27.08.2020 01:01 Arealbot
Moist air at 15°C, 1.3 atm, 63% relative humidity, and a volumetric flow rate of 770 m3/h enters a control volume at steady state and flows along a surface maintained at 187°C through which heat transfer occurs. Liquid water at 15°C is injected at a rate of 7 kg/h and evaporates into the flowing stream. For the control volume, cv = 0, and kinetic and potential energy effects are negligible. If moist air exits at 45°C, 1.3 atm, determine: the rate of heat transfer, in kW. the rate of entropy production, in kW/K.
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
What difference(s) did you notice using a pneumatic circuit over hydraulic circuit.explain why the pneumatic piston stumbles when it hits an obstacle.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
Plot schematically the tensile stress versus strain curves for a typical thermoplastic material at a temperature below its glass transition temperature (tg and at a temperature above its tg, respectively. do the same for a typical thermosetting material. list in a table any differences or similarities between the two materials at t> tg and t < tg, respectively, and relate them to the structures of the two types of polymers
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
A12 mm diameter shaft runs in a plain cylindrical bush 30 mm long that is located in an 18 mm diameter hole in a housing. the shaft-inner bush fit is h8 f and the outer bush-housing fit is h7-p6. make a fully cimensioned sketch of the bush with tolerances. find the maximum and minimum clearance or interference for both fits on the inner and outer diameters of the bush
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
1in2 processor chip can be modelled as an isothermal plane wall of silicon, isothermal on both sides. the power input to the bottom of the plane wall, or the processing power of the chip, often called the thermal design power (tdp), is 100w. assume the periphery is adiabatic. the silicon is 400 microns thick. the temperature at the junction, or in this case on the bottom of the isothermal plane wall, is 85°c. what is the top surface temperature, assuming that the only mode of heat transfer is conduction
Answers: 1
You know the right answer?
Moist air at 15°C, 1.3 atm, 63% relative humidity, and a volumetric flow rate of 770 m3/h enters a c...
Questions
![question](/tpl/images/cats/mkx.png)
Arts, 14.12.2020 20:10
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/istoriya.png)
History, 14.12.2020 20:10
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2020 20:10
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 14.12.2020 20:10
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/ap.png)
Advanced Placement (AP), 14.12.2020 20:10
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 14.12.2020 20:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 14.12.2020 20:10
![question](/tpl/images/cats/mat.png)
Mathematics, 14.12.2020 20:10
![question](/tpl/images/cats/istoriya.png)
History, 14.12.2020 20:10