Engineering, 05.09.2020 23:01 MyChannelBruh6896

Tensile test was conducted on a structural steel specimen with a stem diameter 0.26 in. At failure the measured diameter was 0.145 in. The gage length of the sample at the beginning of the test was 1.800 in. and at failure was 2.280 in. The load/deformation data is given below. Create a stress-strain plot of the data. Include a chart title and axis titles with appropriate units. Required:
a. Calculate the stress-strain data in tabular form
b. Plot the stress-strain diagram
c. Determine the yield strength, ultimate tensile strength, and rupture(breaking) strength
d. Calculate the modulus of elasticity, % elongation, and % reduction in area
e. Compare the values for yield strength and modulus of elasticity with theoretical values
f. Calculate the true stress and true strain at failure
g. Identify the material as brittle or ductile

Load Deformation
lb (ΔL) in.
0 0.0000
100 0.0006
200 0.0007
300 0.0008
400 0.0009
500 0.0011
600 0.0012
700 0.0014
800 0.0015
900 0.0017
1000 0.0018
1100 0.0019
1200 0.0020
1300 0.0022
1400 0.0023
1500 0.0024
1600 0.0026
1700 0.0027
1800 0.0050
1900 0.0100
2000 0.0200
2100 0.0300
2200 0.0400
2300 0.0500
2350 0.0600
2450 0.0700
2550 0.0800
2650 0.0900
2750 0.1000
2850 0.1100
2950 0.1200
3050 0.1300
3150 0.1400
3250 0.1500
3350 0.1700
3450 0.2000
3100 0.2900
2700 0.3900
2280 0.4800

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

What are the two (02) benefits, which may result from a successful implementation of preventive maintenance (pm) program in an organization? (clo3)a)- lean manufacturing b)-overlapping responsibilities c)-the planner is not qualified d)-accurate contractor information e)-reduction in equipment redundancies f)-accurate stores information

Answers: 3

Answer

Engineering, 04.07.2019 19:10

10 kg of co2 is initially contained at 400 kpa and 300 k. the gas constant for carbon dioxide is 189 j/lkg k) and has a specific heat ratio, k, of 1.289. isentropic expansion then occurs until the pressure is 200 kpa. a) determine the initial volume of co2 in m. b) determine the final temperature in k. c) determine the work done by the system during the expansion kl.

Answers: 2

Answer

Engineering, 04.07.2019 19:10

Agas contained within a piston-cylinder assembly e end nation about same energy states, 1 and 2, where pi 10 bar, v undergoes two processes, a and b, between the sam 0.1 m3, ui-400 kj and p2 1 bar, v2 1.0 m2, u2 200 kj: process a: process from 1 to 2 during which the pressure- volume relation is pv constant process b: constant-volume process from state 1 to a pressure of 2 bar, followed by a linear pressure-volume process to +20 0 state 2 kinetic and potential energy effects can be ignored. for each of the processes a and b, (a) sketch the process on p-v coordinates, (b) evaluate the work, in kj, and (c) evaluate process the heat transfer, in kj

Answers: 2

Answer

Engineering, 06.07.2019 02:30

A75mm diameter shaft is supported in a journal bearing 75mm long with a diametral clearance of 0. 1mm. it supports a radial load of 1000 n and is lubricated with sae 50 oil at 70°c. find the friction torque and the power loss when the crankshaft rotates at 2900 rev/min.

Answers: 1

Answer

You know the right answer?

Tensile test was conducted on a structural steel specimen with a stem diameter 0.26 in. At failure t...

Questions