![subject](/tpl/images/cats/User.png)
Engineering, 08.09.2020 14:01 breannaasmith1122
A controlled process is described by the closed-loop transfer function G(s).
G(s) = K(s + 1)/2s^2 + (K-1)s + (K-1)
What values of K will stabilize the process?
(A) K < 1
(B) K > 1
(C) K > 0.75
(D) K > 0
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Give heat transfer applications for the following, (i) gas turbines (propulsion) ) gas turbines (power generation). (iii) steam turbines. (iv) combined heat and power (chp). (v) automotive engines
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
The proportional limit is always greater than the yield strength for a material. a)-trune b)- false
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20
To design a steam turbine to produce 12,000 hp power. a engineer comsiders using a steady state stean low st 1160fr and engineer considers using a steady state steam flow at 1160°r and 450 psia to drive this steam turbine. the exhaust of the steam is cooled by the lake (vacuum). heat losing to the surroundings is measured at a rate of 555.55 btu/s. (a) sketch the system with the given conditions. (b) neglecting kinetic and potential energy changes from inlet to exit, determine the volumetric flow rate of the steam at the inlet, (ft'/hr). must clearly show unit conversions at crtical terms.
Answers: 1
You know the right answer?
A controlled process is described by the closed-loop transfer function G(s).
G(s) = K(s + 1)/2s^2 +...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 17.10.2019 02:50
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 17.10.2019 02:50
![question](/tpl/images/cats/mat.png)
Mathematics, 17.10.2019 02:50
![question](/tpl/images/cats/mat.png)
Mathematics, 17.10.2019 02:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/health.png)
Health, 17.10.2019 02:50
![question](/tpl/images/cats/biologiya.png)
Biology, 17.10.2019 02:50
![question](/tpl/images/cats/fizika.png)
Physics, 17.10.2019 02:50
![question](/tpl/images/cats/mat.png)
Mathematics, 17.10.2019 02:50
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 17.10.2019 02:50
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 17.10.2019 02:50
![question](/tpl/images/cats/mat.png)
Mathematics, 17.10.2019 02:50
![question](/tpl/images/cats/en.png)