Engineering, 22.09.2020 20:01 calraezaj2020

Piessunzed water (pin-10 bar, Tin= 1 10°C) enters the hottom of an L 12-m-long vertical tube of diameter D110 mm at a mass flow rate of 1.5kg/s. The tube is located inside a combustion chamber, resulting in heat transfer to the tube. Superheated steam exits the top of the tube at o 7 bar, T 600°C. Determine the change in the rate at which the following quantities enter and exit the tube: (a) the combined thermal and Row work, (b) the mechanical energy, and
(c) the total energy of the water. Also, (d) determine the heat trans- fer rate. q. Hint: Relevant properties may be obtained from a thermodynamics text.
Consider the tube and inlet conditions above Heat transfer at a rate of 3.89 MW is delivered to the tube. For an exit pressure of p 8 bar, determine
(a) the temperature of the water at the outlet as well as the change in
(b) combined thermal and flow work,
(c) mechanical energy, and (d) total energy of the water from the inlet to the outlet of the tube. Hint: As a first estimate, neglect the change in mechanical energy in solving part (a). Relevant properties may be obtained from a thermodynamics text

Answers: 2

Show answers

Answers

Answer from: tmcdowell69

(1) $\Delta E_{tw}=4845.43 kW$

(2) $\Delta E_m=6.329 kW$

(3) $\Delta E_t= 4851.759 kW$

(4) q= 4851.759 kW

Explanation:

At the saturation temperature, water starts boiling, and before that heat is added at constant pressure as latent heat.

From the saturated water-pressure table, at the pressure P=10 bar, we have

The saturated temperature of the water, $T_{sw}=179.88^{\circ} C$

The specific volume of water, $v_{ws}=v_f=0.00127 m^3/kg$

Specific enthalpy of water, $h_{ws}=h_f=762.50 kJ/kg$

The given inlet temperature of the water, $T_i=110^{\circ}$ , so, latent heat added to the water to reach the saturation temperature is

$h_l=C_P(T_{sw}-T_i)$

$\Rightarrow h_l=4.187(179.88^{\circ} -110^{\circ}$

$\Rightarrow h_l=292.587 kJ/kg$

Now, specific enthalpy of the water at the inlet (specific enthalpy of the water at the saturation temperature) (Latent heat capacity).

$\Rightarrow h_i=h_{sw}-h_l$

$\Rightarrow h_i=762.50-292.587=469.912kJ/kg$

The specific volume of the water at intel is the same as the specific volume at the saturation temperature as volume remains unchanged on the addition of latent heat.

So, $v_i=v_{ws}=0.00127 m^3/kg$ .

The outlet temperature, $T_o=600^{\circ} C$ and pressure, P_o=7 bar. From the superheated water table, we have

The specific volume of water, v_o=0.5738 m^3/kg

The specific enthalpy of water, $h_{wo}=3700.9 kJ/kg$

The given mass flow rate, $\dot{m} =1.5 kg/s$ .

The inlet radius and outlet diameter are the same, i.e

d_i=d_o=110 mm=0.11m .

So, Inlet and outlet areas, $A_i=A_f=9.5033\times 10^{-3} m^2$ .

Let the inlet and outlet velocities be V_i and V_o respectively.

For the given specific volume, , and mass flow rate, $\dot{m}$ , the velocity, , at any cross-section having an area is

$V=\frac{v\dot{m}}{A}$ .

So, the inlet velocity,

$V_i=\frac{v_i \dot{m}}{A_i}$

$\Rightarrow V_i=\frac{0.00127\times 1.5}{9.5033\times 10^{-3}}$

$\Rightarrow V_i=0.20 m/s$ .

Similarly, the outlet velocity,

$V_o=\frac{v_o \dot{m}}{A_o}$

$\Rightarrow V_o=\frac{0.5738\times 1.5}{9.5033\times 10^{-3}}$

$\Rightarrow V_0=90.57 m/s$ .

(1) The change in combined thermal energy and work flow Change in the thermal energy Change in the flow work

$\Delta E_{tw}= \dot{m}(u_f-u_i)+\dot{m} (P_fv_f-P_iv_i)$

$\Rightarrow \Delta E_{tw}=\dot{m}[(u_f+P_fv_f) - (u_i+P_iv_i)$

$\Rightarrow \Delta E_{tw}=\dot{m} (h_f-h_i)$

$\Rightarrow \Delta E_{tw}=1.5(3700,20-469.912)=4845.43 kW$

(2)The change in mechanical energy

$\Delta E_m=$ Change in kinetic energy + change in potential energy

$\Rightarrow \Delta E_m=\left(\frac 1 2 \dot{m} V_f^2-\frac 1 2 \dot{m} V_i^2\right)+(\dot{m} g z_f-\dot{m} g z_i)$

$\Rightarrow \Delta E_m=\frac 1 2 \dot{m}(V_f^2-V_i^2)+\dot{m} g (z_f-z_i)$

$\Rightarrow \Delta E_m=\frac 1 2\times 1.5((90.57)^2-(0.2)^2)+1.5 \times 9.81 \times12$

$\Rightarrow \Delta E_m=6328.74 J/s=6.329 kW$

(3) The change in the total energy of water,

$\Delta E_t=$ chnge in the thernal energy + change in the flow work + change in the mechanical energy

$\Rightarrow \Delta E_t=4845.43+6.329= 4851.759 kW$ [from part (1) and (2)]

(4) Now, as there is no work done by the water, so, the heat input only caused the change in the total energy.

Hence, the rate of heat transfer, q= 4851.759 kW [from part (3).

Answer from: Quest

1.jews

2.poles

3.russians

4.gypsies

5. african americans

< 3

Answer from: Quest

answer:

okay

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Journeyman training is usually related (clo2) a)-to specific tasks b)-to cost analysis of maintenance task c)-to control process to ensure quality d)-to installation of machinery

Answers: 2

Answer

Engineering, 04.07.2019 18:20

An engine runs on the ideal diesel cycle. the cycle has a compression ratio of 20 and a cutoff ratio of 2. the highest temperature in the cycle is 1200 k. if the heat into the system is 300 kj/kg of working fluid and using variable specific heats determine the work produced per mass of working fluid

Answers: 3

Answer

You know the right answer?

Piessunzed water (pin-10 bar, Tin= 1 10°C) enters the hottom of an L 12-m-long vertical tube of diam...

Questions