Engineering, 15.10.2020 08:01 BIKRAMlawati9684

A large V8 SI four-stroke cycle engine with displacement of 4.6 liters is equipped with cylinder cutout, which converts the engine to a 2.3 liter V4 when less power is needed. At a speed of 1750 RPM the engine, as a V8, has a volumetric efficiency of 51%, a mechanical efficiency of 75%, an air-fuel ratio of 14.5, and produces 32.4 kW of brake power using gasoline. With cylinder cutout and operating at higher speed as a V4, the engine has a volumetric efficiency of 86%, a mechanical efficiency of 87%, and uses an air-fuel ratio of 18.2. Indicated thermal efficiency can be considered the same at all speeds, and combustion efficiency is 100%. Calculate : a) Mass flow rate of air into V8 engine at 1750 RPM. [kg/sec]
b) Mass flow rate of fuel into V8 engine at 1750 RPM. [kg/sec]
c) The bsfc as V8 at 1750 RPM. [gram/kW-hr]
d) Engine speed needed as a V4 to produce same brake power output. [RPM]
e) The bsfc as V4 at higher speed. [gram/kW-hr]

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan

Answers: 3

Answer

Engineering, 04.07.2019 19:10

Agas contained within a piston-cylinder assembly e end nation about same energy states, 1 and 2, where pi 10 bar, v undergoes two processes, a and b, between the sam 0.1 m3, ui-400 kj and p2 1 bar, v2 1.0 m2, u2 200 kj: process a: process from 1 to 2 during which the pressure- volume relation is pv constant process b: constant-volume process from state 1 to a pressure of 2 bar, followed by a linear pressure-volume process to +20 0 state 2 kinetic and potential energy effects can be ignored. for each of the processes a and b, (a) sketch the process on p-v coordinates, (b) evaluate the work, in kj, and (c) evaluate process the heat transfer, in kj

Answers: 2

Answer

Engineering, 04.07.2019 19:20

Determine the time of the day and month of the year at which the peak sensible cooling load occurs for a top floor, north-eastern corner room of an office building in durban for the following conditions: floor area: 8 x 8 x 3 m east and north walls: 115 mm face brick (outside), 20 mm air space, 115 mm ordinary brick (inside) with 15 mm plaster roof construction: suspended plasterboard ceiling, 450 mm air space, 150 mm concrete, 75mm screed, waterproofing no heat transfer across other surfaces window area 3x 1,5 m high in north wall only. ordinary glass with venetian blinds. lights and occupants : from 07: 00 to 18: 00 average light density: 25 w/m2 number of occupants : 5 seated, light office work room temperature 24°c

Answers: 3

Answer

You know the right answer?

A large V8 SI four-stroke cycle engine with displacement of 4.6 liters is equipped with cylinder cut...

Questions