If carpet costs $3.25 a square foot, what would it
cost to replace a 200 square foot room?...
![subject](/tpl/images/cats/User.png)
Engineering, 12.11.2020 21:30 James17syoboda
If carpet costs $3.25 a square foot, what would it
cost to replace a 200 square foot room?
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aflywheel accelerates for 5 seconds at 2 rad/s2 from a speed of 20 rpm. determine the total number of revolutions of the flywheel during the period of its acceleration. a.5.65 b.8.43 c. 723 d.6.86
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Questions
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:00
![question](/tpl/images/cats/User.png)
SAT, 04.03.2021 17:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 04.03.2021 17:10
![question](/tpl/images/cats/en.png)
English, 04.03.2021 17:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/health.png)
Health, 04.03.2021 17:10
![question](/tpl/images/cats/en.png)
English, 04.03.2021 17:10
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10
![question](/tpl/images/cats/biologiya.png)
Biology, 04.03.2021 17:10
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 17:10