Engineering, 23.12.2020 23:50 zahwaahmaf

Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz 1. How is diesel fuel ignited in a warm diesel engine?
A. Glow plugs
B. Heat compression
C. Spark plugs
D. Distributor-less ignition system

2. Which type of diesel injection produces less noise?
A. Indirect injection (IDI)
B. Common rail
C. Direct injection
D. Distributor injection

3. Which diesel injection system requires the use of a glow plug?
A. Indirect injection (IDI)
B. High pressure common rail
C. Direct injection
D. Distributor injection

4. The three phases of diesel ignition include .
A. Glow plug ignition, fast burn, slow burn
B. Slow burn, fast burn, slow burn
C. Ignition delay, repaid combustion, controlled combustion
D. Glow plug ignition, ignition delay, controlled combustion

5. What fuel system component is used in a vehicle equipped with a diesel engine that is seldom used on the same vehicle when it is equipped with a gasoline engine?
A. Fuel filter
B. Fuel supply line
C. Fuel return line
D. Water-fuel separator

6. The diesel injection pump is usually driven by a .
A. Gear off the camshaft
B. Belt off the crankshaft
C. Shaft drive off of the crankshaft
D. Chain drive off of the camshaft

7. Which diesel system supplies high-pressure diesel fuel to all the injectors all of the time?
A. Distributor
B. Inline
C. High-pressure common rail
D. Rotary

8. Glow plugs should have high resistance when and lower resistance when .
A. Cold/warm
B. Warm/cold
C. Wet/dry
D. Dry/wet

9. Technician A says that glow plugs are used to help start a diesel engine and are shut off as soon as the engine starts. Technician B says that the glow plugs are turned off as soon as a flame is detected in the combustion chamber. Which Technician is correct?
A. Technician A only
B. Technician B only
C. Both Technicians A and B
D. Neither Technicians A NOR B

10. What part should be removed to test cylinder compression on a diesel engine?
A. An injector
B. An intake valve rocker arm and stud
C. An exhaust valve
D. A glow plug

Answers: 3

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10

Answers: 1

Answer

Engineering, 04.07.2019 18:20

Select any two (2) areas of applications of chain-drive. (clo4) a)-permanent lubrication necessary b)-hydraulic forklift truck operation c)-rigging and heavy moving materials d)-relatively high maintenance costs e)-costlier than belt drives

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Describe one experiment in which the glass transition temperature and melting temperature of a totally amorphous thermoplastic material can be determined. show the relevant experimental results in a diagram which should be properly annotated with the two temperatures clearly marked. what is likely to happen to the curve in the diagram if the amorphous polymer is replaced by a thermosetting type?

Answers: 2

Answer

Engineering, 04.07.2019 19:20

To save energy, the air supply to a 2000 ft office has been shut off overnight and the room temperature has dropped to 40°f. in the morning, the thermostat is reset to 70°f and warm air at 120 f begins to flov in at 200ft'/min. the air is well mixed within the room, and an equal mass flow of air at room temperature (changing with time) is withdrawn through a return duct. the air pressure is nearly 1 atm everywhere. ignoring heat transfer with the surroundings and kinetic and potential energy effects, estimate how long it takes for the room temperature to reach 70°f. plot the room temperature as a function of time.

Answers: 1

Answer

You know the right answer?

Chapter 19: Diesel Engine Operation and Diagnosis -Chapter Quiz 1. How is diesel fuel ignited in a...

Questions