Engineering, 25.03.2021 20:10 leapfroggiez

To design a dc bias circuit, some reasonable approximations may be used. The first assumption is the voltage from emitter to ground. VE is typically one-fifth to one-tenth of the

supply voltage, VCC. Selecting the emitter voltage in this way will permit calculating the

emitter resistance, RE and then the collector resistance, RC by using the following equations:

VE ≈ 1 / 10 VCC

RE ≈ VE / IC

RC = (VCC - VCE - VE) / IC

Hence, the base voltage is approximately equal to the emitter voltage,

or more exactly, VB = VE + VBE.

Finally, determine the values for the base resistors, RB1 and RB2 by approximating

RB2 ≤ 1/ 10 ( βRE )

RB1 can be obtained by using the following equation,

VB = RB2

/ (RB2 + RB1 ) ( VCC )

Now, by referring to the proposed circuit as shown in Figure 1, select appropriate values for

RB1

, RB2

, RC and RE. Simulate the circuit and print the output waveform, Vo for a sinusoidal

input signal of 10mV at frequency 1kHz.

To design a dc bias circuit, some reasonable approximations may be used. The first

assumption is

Answers: 1

Show answers

Another question on Engineering

Engineering, 03.07.2019 15:10

Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

Answer

You know the right answer?

To design a dc bias circuit, some reasonable approximations may be used. The first assumption is th...

Questions