![subject](/tpl/images/cats/User.png)
Engineering, 28.05.2021 21:30 chancecharles9oug353
When you're running a test bench, you would like to include a printout to the screen to inform yourself on the status of the current simulation. Which command you could use to monitor specific variables or signals in a simulation every time one of the signals changes value?
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
Along 8-cm diameter steam pipe whose external surface temperature is 900c connects two buildings. the pipe is exposed to ambient air at 70c with a wind speed of 50 km/hr blowing across the pipe. determine the heat loss from the pipe per unit length. (b) air at 500c enters a section of a rectangular duct (15 cm x 20 cm) at an average velocity of 7 m/s. if the walls of the duct are maintained at 100c. a) the length of the tube for an exit temperature of the air to be 40 0c. b)the rate of heat transfer from the air. c) the fan power needed to overcome the pressure drop in this section of the duct.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
What is a monomer? how do they form a ploymer from the view point of chemical bonding?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
1in2 processor chip can be modelled as an isothermal plane wall of silicon, isothermal on both sides. the power input to the bottom of the plane wall, or the processing power of the chip, often called the thermal design power (tdp), is 100w. assume the periphery is adiabatic. the silicon is 400 microns thick. the temperature at the junction, or in this case on the bottom of the isothermal plane wall, is 85°c. what is the top surface temperature, assuming that the only mode of heat transfer is conduction
Answers: 1
You know the right answer?
When you're running a test bench, you would like to include a printout to the screen to inform yours...
Questions
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/en.png)
English, 21.04.2020 20:57
![question](/tpl/images/cats/biologiya.png)
Biology, 21.04.2020 20:57
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 21.04.2020 20:57
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 21.04.2020 20:57
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/istoriya.png)
History, 21.04.2020 20:57
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 21.04.2020 20:57
![question](/tpl/images/cats/en.png)
English, 21.04.2020 20:57