subject
Engineering, 16.06.2021 17:50 Benjamincompton07

A school teacher must schedule seven sessions, which are abbreviated M, N, O, P, S, T, and U, during a day. Seven different consecutive time periods are available for the sessions, and are numbered one through seven in the order that they occur. Only one session can be schedules for each period. The assignment of the sessions to the periods is subject to the following restrictions: M and O must occupy consecutive periods. M must be scheduled for an earlier period than U.
O must be scheduled for a later period than S.
If S does not occupy the fourth period, then P must occupy the fourth period.
U and T cannot occupy consecutively numbered periods.

Which of the following could be true?
a. M is assigned to the first period.
b. O is assigned to the fifth period.
c. S is assigned to the seventh period.
d. T is assigned to the sixth period.

ansver
Answers: 2

Another question on Engineering

question
Engineering, 03.07.2019 14:10
Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.
Answers: 3
question
Engineering, 04.07.2019 18:10
Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.
Answers: 3
question
Engineering, 04.07.2019 18:20
Find the minimum film thickness for a journal bearing with the data below. shaft diameter, d-50 mm, clearance ratio, cdratio? 0.001, shaft speed, n 2000 rpm; bearing length. i 200 mm; eccentricity ration, ? -0.55. ( note, cdratio-ca/d) the minimum film thickness is um
Answers: 2
question
Engineering, 04.07.2019 18:20
Aheavily insulated piston-cylinder device contains 0.02 m3 of steam at 300 kpa and 200 °c. 1.2 mpa. d this process. team is now compressed in a reversible manner to a pressure of etermine the entropy change and the work done on the steam during this process
Answers: 1
You know the right answer?
A school teacher must schedule seven sessions, which are abbreviated M, N, O, P, S, T, and U, during...
Questions
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Physics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Geography, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Physics, 13.09.2020 08:01
question
History, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
Mathematics, 13.09.2020 08:01
question
English, 13.09.2020 08:01
Questions on the website: 13722363