![subject](/tpl/images/cats/User.png)
Engineering, 21.07.2021 22:00 yam78
Draw a synchronous decade counter, using J K flip-flops like the one below. As well as the flip-flops you can use as many AND, OR, NAND, NOT, etc. gates as you need. Note there are no asynchronous set or reset inputs so you need to use logic to count and reset. What is the modulus and how many flip-flops are needed?
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 15:10
If you were designing a bumper for a car, would you prefer it to exhibit elastic or plastic deformation? why? consider the functions of a bumper in both a minor "fender-bender" and a major collision.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 16:10
An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
A12 mm diameter shaft runs in a plain cylindrical bush 30 mm long that is located in an 18 mm diameter hole in a housing. the shaft-inner bush fit is h8 f and the outer bush-housing fit is h7-p6. make a fully cimensioned sketch of the bush with tolerances. find the maximum and minimum clearance or interference for both fits on the inner and outer diameters of the bush
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
A75mm diameter shaft is supported in a journal bearing 75mm long with a diametral clearance of 0. 1mm. it supports a radial load of 1000 n and is lubricated with sae 50 oil at 70ยฐc. find the friction torque and the power loss when the crankshaft rotates at 2900 rev/min.
Answers: 1
You know the right answer?
Draw a synchronous decade counter, using J K flip-flops like the one below. As well as the flip-flop...
Questions
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 03.07.2019 23:20
![question](/tpl/images/cats/mat.png)
Mathematics, 03.07.2019 23:20
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.07.2019 23:20
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/istoriya.png)
History, 03.07.2019 23:20
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.07.2019 23:20
![question](/tpl/images/cats/mat.png)
Mathematics, 03.07.2019 23:20
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 03.07.2019 23:20
![question](/tpl/images/cats/mat.png)