subject
Engineering, 28.07.2021 04:30 jayjinks976

Consider the 2D motion of a rocket moving around the Earth. Consider Earth as being stationary and the attractive force i induces on the rocket is directed towards the center of the Earth and has a magnitude of In the equation r is the current distance of the rocket from the center of the Earth . RE 6371 km is the radius of the Earth m is the mass of the rocket g 9.81 m/s2 is the usual acceleration due to gravity (on the Earth's surface) a) Write the equations of motion of the rocket in an appropriate polar coordinate system. b) Integrate the equations of motion for the system numerically using MATLAB and ode45 for the conditions shown below. The initial distance between the rocket and the Earth is ro. The initial velocity of the rocket towards the center of the Earth and perpendicular to it are given by vr and ve respectively. Assume that the angle 8 is zero initially and that ro-5RE and vr 0. Carry out the integration at a time step of 10s for 80,000 time steps (i. e., a total simulation time of 800,000 seconds) for each of the initial velocities specified below: For each condition, plot the trajectory of the rocket for the requested time and plot the two components v and ve of the velocity as a function of time. For the trajectory, you may plot the two Cartesian coordinates defined by x = r cos θ an yrsin 6 that you can evaluate numerically once you have the values of r and Note that the trajectories will be (a) a circle, (b) an ellipse, (c) a parabola, and (d) a hyperbola. Case (c) is the escape velocity - the lowest velocity for which the particle will leave the Earth's attractive influence. Use the MATLAB "axis equal" command in the trajectory plots, to see the shape of trajectory in proper scale.

ansver
Answers: 1

Another question on Engineering

question
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
question
Engineering, 04.07.2019 18:10
Apipe with an outside diameter of 15 cm is exposed to an ambient air and surrounding temperature of -20°c. the pipe has an outer surface temperature of 65°c and an emissivity of 0.85. if the rate of heat loss from the pipe surface is 0.95 kw per meter of length, the external convective heat transfer coefficient (h) is: (a) 12.5 w/m"k (b) 18.6 w/mk (c) 23.7 w/mk (d) 27.9 w/mk (e) 33.5 w/mk
Answers: 1
question
Engineering, 04.07.2019 18:10
Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)
Answers: 3
question
Engineering, 04.07.2019 18:10
Machinery that is a key part of the process and without which the plant or process cannot function is classifed as: (clo4) a)-critical machinery b)-essential machinery c)-general purpose machinery d)-none of the specified options.
Answers: 1
You know the right answer?
Consider the 2D motion of a rocket moving around the Earth. Consider Earth as being stationary and t...
Questions
question
Mathematics, 29.01.2021 05:20
question
English, 29.01.2021 05:20
question
Biology, 29.01.2021 05:20
question
Mathematics, 29.01.2021 05:20
question
History, 29.01.2021 05:20
Questions on the website: 13722361