![subject](/tpl/images/cats/User.png)
Engineering, 09.09.2021 15:30 babygirl091502
Question 4: [15] You have two identical pieces of copper, each weighing 200 g, in contact with each other, the temperature of the one being 900°C, that of the other 75°C. Heat transfer should only be between the two metal pieces, but not with the surroundings. 4.1 What will happen to the temperature of the copper pieces? (5) 4.2 Is what is happening reversible or irreversible (spontaneous)? (5) 4.3 Calculate the change of entropy that occurs (use mean heat capacity value for copper) (5) 3 21°C A 15 3
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 15:10
Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 23:20
Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
What difference(s) did you notice using a pneumatic circuit over hydraulic circuit.explain why the pneumatic piston stumbles when it hits an obstacle.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
You know the right answer?
Question 4: [15] You have two identical pieces of copper, each weighing 200 g, in contact with each...
Questions
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 23:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 04.03.2021 23:00
![question](/tpl/images/cats/health.png)
Health, 04.03.2021 23:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 23:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 23:00
![question](/tpl/images/cats/istoriya.png)
History, 04.03.2021 23:00
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/istoriya.png)
History, 04.03.2021 23:00
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.03.2021 23:00
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 04.03.2021 23:00
![question](/tpl/images/cats/istoriya.png)
History, 04.03.2021 23:00