subject
Engineering, 06.12.2021 19:50 jslaughter3

A mixture of air and a fine spray of gasoline at ambient (outside air) temperature is fed to a set of pistonfitted cylinders in an automobile engine. Sparks ignite the combustible mixtures in one cylinder after another, and the consequent rapid increase in temperature in the cylinders causes the combustion products to expand and drive the pistons. The back-and-forth motion of the pistons is converted to rotary motion of a crank shaft, motion that in turn is transmitted through a system of shafts and gears to propel the car. Consider a car driving on a day when the ambient temperature is 298K and suppose that the rate of heat loss from the engine to the outside air is given by the formula:
-Q1(kj/h) ~ 15x10^6/Ta(k)
where Ta is the ambient temperature.
a. Take gasoline to be a liquid with a specific gravity of 0.70 and a higher heating value of 49.0 kJ/g, assume complete combustion and that the combustion products leaving the engine are at 298 K, and calculate the minimum feed rate of gasoline (gal/h) required to produce 100 hp of shaft work.
b. If the exhaust gases are well above 298 K (which they are), is the work delivered by the pistons more or less than the value determined in Part a)? Explain.
If the ambient temperature is much lower than 298 K, the work delivered by the pistons would decrease. Give two reasons.

ansver
Answers: 1

Another question on Engineering

question
Engineering, 03.07.2019 23:20
Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct
Answers: 3
question
Engineering, 04.07.2019 18:10
Abrake has a normal braking torque of 2.8 kip in and heat-dissipating cast-iron surfaces whose mass is 40 lbm. suppose a load is brought to rest in 8.0 s from an initial angular speed of 1600 rev/min using the normal braking torque; estimate the temperature rise of the heat dissipating surfaces.
Answers: 3
question
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
question
Engineering, 04.07.2019 18:10
Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.
Answers: 3
You know the right answer?
A mixture of air and a fine spray of gasoline at ambient (outside air) temperature is fed to a set o...
Questions
question
Biology, 04.06.2020 06:58
question
Mathematics, 04.06.2020 06:58
question
Mathematics, 04.06.2020 06:58
question
Engineering, 04.06.2020 06:58
question
History, 04.06.2020 06:58
question
English, 04.06.2020 06:58
Questions on the website: 13722362