The meals ready to eat in the military can be heated on a flameless heater. You can purchase a similar product called heater meals. Just pour water into the heater unit wait a few minutes and you have a hot meal. The source of energy is Mg(s) + 2H2O(l) > Mg(OH)2(s) + H2(g)
Calculate the enthalpy change under standard conditions, in joules, for this reaction. What quantity of magnesium is needed to supply the energy required to warm 25ml (1.00g/ml) from 25C to 85C?
Now the first part I calculated -352.88kj for the enthalpy change, which was correct. Now when I get to the second part I have some trouble. Normally I would set it up as
q1+q2=0 Where the energy release and absorbed equal zero because both come to thermal equilibrium. So I proceed with naming q1 the water.
q1= (4.184J/g. C)(25g)(60C)= 6276J. So in order to increase 25g of water 60C, you need 6276J. Now this is where I am stuck, the problem doesn't give the specific heat capacity for the magnesium, so I looked it up and did this
q2= (1.20J/g. C)(x)(60)... now this is where I think i did something wrong, not only because when i do this i do not get the right answer, but because the temperature values for the magnesium were not given. Can someone help me out with this problem? I feel I have to use the enthalpy change value to eventually get the amount of Magnesium required.

answer: i guess 5 units?

step-by-step explanation:

answer: 1000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

step-by-step explanation:

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).