subject

Mathematics, 11.02.2021 22:40 alexantkoviak13

S=4w+12 plz

S=4w+12 plzzzzzzzzzzzzzzzzzzzzzzzzzzzz

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 16:00

Successful implementation of a new system is based on three independent modules. module 1 works properly with probability 0.96. for modules 2 and 3, these probabilities equal 0.95 and 0.90. compute the probability that at least one of these three modules fails to work properly.

Answers: 2

question

Mathematics, 21.06.2019 23:30

Tatiana wants to give friendship bracelets to her 32 classmates. she already has 5 bracelets, and she can buy more bracelets in packages of 4. write an inequality to determine the number of packages, p, tatiana could buy to have enough bracelets.

Answers: 1

question

Mathematics, 21.06.2019 23:30

Drag each equation to the correct location on the table. for each equation, determine the number of solutions and place on the appropriate field in the table.

Answers: 3

question

Mathematics, 22.06.2019 00:20

Given: jk ||lm prove: _2 = 27 statement justification 1. jk ||lm 1. given 2.26 = 27 3.22 = 26 2. 3. 4. _2 = 27 4. corresponding angles theorem transitive property of equality vertical angles theorem substitution property of equality

Answers: 1

You know the right answer?

S=4w+12 plz
...

Questions

question

Engineering, 26.07.2019 17:20

If a cutting operation is performed at a feed rate of 5 in/min, and the feed is 0,005 in/rev, then the spindle rpm is: i. 5000 rpm. i. 1000 rpm. ili....

question

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

question

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

question

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

question

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

question

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

question

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

question

Engineering, 26.07.2019 17:20

5kg of wood is burnt in an insulated room. take the walls of the room as well as the wood as the system. the internal energy of the room will increase...

question

Engineering, 26.07.2019 17:20

The hardness of a cutting tool increases with increasing temperature. thus, it is always convenient to machine at higher speeds that lead to higher te...

question

Engineering, 26.07.2019 17:20

What are the independent and dependent variables that are taken into account during journal bearing design?...

question

Engineering, 26.07.2019 17:20

You are provided with an epicyclic (planetary) gear train with the following 30, 20 and 70 teeth on the sun, planet and ring gear respectively. (a) dr...

question

Engineering, 26.07.2019 17:20

What is a partial bearing? what is a loading situation that might lead you to use a partial bearing? how did this tie into beauchamp tower's experim...

question

Engineering, 26.07.2019 17:20

Define and give a few benefits of each of three gear train design options?...

question

Engineering, 26.07.2019 17:20

The atmospheric pressure at the top and the bottom of a mountain are read to be 93.8 kpa and 100.5 kpa respectively. if the average density of air is...

question

Engineering, 26.07.2019 17:20

What are some of the assumptions that were used in developing the 1d reynolds flow equation?...

question

Engineering, 26.07.2019 17:20

Acar engine rotates at a speed of 3500 rpm and transmits 290 kw. determine the torque applied to the crankshaft of the car a)- 791.2 n. m b)- 1108 n....

question

Engineering, 26.07.2019 17:20

The pressure of a fluid at rest changes with vertical distance but remains the same in the horizontal direction a)-true b)-false...

question

Engineering, 26.07.2019 17:20

Agear set uses of an 18-tooth pinion, has a diametral pitch of 8 teeth in and a pressure angle of ? -20 . the pinion runs at 750 rev/min and drives a...

question

Engineering, 26.07.2019 17:20

Aresistor heater is used for heating water for 3 minute at 120 volts and s amps. how much of the electrical power is consumed? a)- 1800w b)- 108 kw c...

More questions: Mathematics Another questions

Questions on the website: 13722361