subject

Mathematics, 12.05.2021 21:20 cici170

Find the exact value of sin(0)
A. 0.0161
B. 0.7975
C. 12/13
D. 12/5

Find the exact value of sin(0)
A. 0.0161
B. 0.7975
C. 12/13
D. 12/5

ansver

Answers: 2

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 16:00

Aswim teacher sells lesson packages. the best deal has the highest ratio of lessons to total cost.swim lesson packagesnumber of lessons total cost$10$4010 1 $8015$80which package is the best deal? l lesson for $105 lessons for $4010 lessons for $8015 lessons for $80mark this and returnsave and exit

Answers: 3

question

Mathematics, 21.06.2019 21:10

What is the measure of one interior angle of a pentagon

Answers: 2

question

Mathematics, 21.06.2019 23:00

Which geometric principle is used to justify the construction below?

Answers: 1

question

Mathematics, 21.06.2019 23:00

The measurement of one angle of a right triangle is 42° what is the measurement of the third angle? (there is no picture)

Answers: 1

You know the right answer?

Find the exact value of sin(0)
A. 0.0161
B. 0.7975
C. 12/13
D. 12/5
...

Questions

question

Engineering, 26.07.2019 20:10

How does the thermal efficiency of an ideal cycle, in general, compare to that of a carnot cycle operating between the same temperature limits?...

question

Engineering, 26.07.2019 20:10

Agas turbine cycle using brayton cycle with both intercooler and regenerators air and split ideal compressor and turbine, enters in the compressor at...

question

Engineering, 26.07.2019 20:10

Define the isentropic efficiency for each of the following 3. a. i. adiabatic turbine ii. adiabatic compressor iii. adiabatic nozzle...

question

Engineering, 26.07.2019 20:10

What causes a shock to detach from the surface of an object?...

question

Engineering, 26.07.2019 20:10

Consider two solid blocks, one hot and the other cold, brought into contact in an adiabatic container. after a while, thermal equilibrium is establish...

question

Engineering, 26.07.2019 20:10

Steam at 500 psia and 600 f is cooled at constant volume to the state of 100 psia. the heat removed from the steam enters the environment at 60 f. fin...

question

Engineering, 26.07.2019 20:10

Avolcanic plume puts ash into the atmosphere to altitude of 1m. the characteristic ash particle is a sphere with a diameter of 40 um and has a density...

question

Engineering, 26.07.2019 20:10

Consider a steam power plant that operates on the ideal reheat rankine cycle. the plant maintains the boiler at 5,000 kpa, the reheat section at 1,200...

question

Engineering, 26.07.2019 20:10

Pressurized steam at 540 k flows through a long, thin-walled pipe of 0.6-m diameter. the pipe is enclosed in a concrete casing that is of square cross...

question

Engineering, 26.07.2019 20:10

Rank the six microstructures of steel in general order of least ductile to most ductile.(bainite, coarse pearlite, fine pearlite, martensite, spheroid...

question

Engineering, 26.07.2019 20:10

In regard to low pressure die casting, high pressure die casting and squeeze casting of aluminium alloys, briefly compare the following process charac...

question

Engineering, 26.07.2019 20:10

A2d, incompressible flow field is described by the stream function φ= -(ax^2-ay^2). a. is the flow possible? b. is the flow field a potential flow fi...

question

Engineering, 26.07.2019 20:10

(a) briefly describe, aided with schematic drawings, the operation principles of the two 6. powder bed (selective laser melting and selective electron...

question

Engineering, 26.07.2019 20:10

Steam at a pressure of 15 bar and a temperature of 320 °c is contained in a large vessel. connected to the vessel through a valve is a turbine followe...

question

Engineering, 26.07.2019 20:10

Awaste gas stream containing 190 ppm by volume ) vinyl chloride is to be treated with activated carbon ina packed bed at a rate of 20 m3/min to reduce...

question

Engineering, 26.07.2019 20:10

Casting of a plate is made in a metal mould where heat transfer is controlled at the mould- metal interface. ignore the superheat of the liquid metal...

question

Engineering, 26.07.2019 20:10

Consider two long, poles of same diameter and uniform cross sectional area throughout its length but different materials. the ends of each rod is atta...

question

Engineering, 26.07.2019 20:10

What is the quality of a two-phase liquid-vapor mixture of h20 at 20 °c with a specific volume of 10 m^3/kg?...

question

Engineering, 26.07.2019 20:10

Consider cutting tool materials, answer which cutting material is suitable, considering manufacturing costs, for each of the major metallic alloy (al...

question

Engineering, 26.07.2019 20:10

Describe the challenges associated with fusion welding of dissimilar metals. your description should cover all the parameters and /or factors to be co...

More questions: Mathematics Another questions

Questions on the website: 13722359