Physics, 01.10.2019 06:40 AutumnJoy12

How do you change the currents in a circuit

Answers: 1

Show answers

Answers

-
Eddy Current Testing

Introduction
Basic Principles
History of ET
Present State of ET

The Physics
Properties of Electricity
Current Flow & Ohm's Law
Induction & Inductance
Self Inductance
Mutual Inductance
Circuits & Phase
Impedance
Depth & Current Density
Phase Lag

Instrumentation
Eddy Current Instruments
Resonant Circuits
Bridges
Impedance Plane
Display - Analog Meter

Probes (Coils)
Probes - Mode of Operation
Probes - Configuration
Probes - Shielding
Coil Design
Impedance Matching

Procedures Issues
Reference Standards
Signal Filtering

Applications
Surface Breaking Cracks
SBC using Sliding Probes
Tube Inspection
Conductivity
Heat Treat Verification
Thickness of Thin Mat'ls
Thickness of Coatings

Advanced Techniques
Scanning
Multi-Frequency Tech.
Swept Frequency Tech.
Pulsed ET Tech.
Background Pulsed ET
Remote Field Tech.

Quizzes

Formulae& Tables
EC Standards & Methods
EC Material Properties
-

Current Flow and Ohm's Law

Ohm's law is the most important, basic law of electricity. It defines the relationship between the three fundamental electrical quantities: current, voltage, and resistance. When a voltage is applied to a circuit containing only resistive elements (i.e. no coils), current flows according to Ohm's Law, which is shown below.

I = V / R

Where:

I =

Electrical Current (Amperes)

V =

Voltage (Voltage)

R =

Resistance (Ohms)

Ohm's law states that the electrical current (I) flowing in an circuit is proportional to the voltage (V) and inversely proportional to the resistance (R). Therefore, if the voltage is increased, the current will increase provided the resistance of the circuit does not change. Similarly, increasing the resistance of the circuit will lower the current flow if the voltage is not changed. The formula can be reorganized so that the relationship can easily be seen for all of the three variables.

The Java applet below allows the user to vary each of these three parameters in Ohm's Law and see the effect on the other two parameters. Values may be input into the dialog boxes, or the resistance and voltage may also be varied by moving the arrows in the applet. Current and voltage are shown as they would be displayed on an oscilloscope with the X-axis being time and the Y-axis being the amplitude of the current or voltage. Ohm's Law is valid for both direct current (DC) and alternating current (AC). Note that in AC circuits consisting of purely resistive elements, the current and voltage are always in phase with each other.

Exercise: Use the interactive applet below to investigate the relationship of the variables in Ohm's law. Vary the voltage in the circuit by clicking and dragging the head of the arrow, which is marked with the V. The resistance in the circuit can be increased by dragging the arrow head under the variable resister, which is marked R. Please note that the vertical scale of the oscilloscope screen automatically adjusts to reflect the value of the current.

See what happens to the voltage and current as the resistance in the circuit is increased. What happens if there is not enough resistance in a circuit? If the resistance is increased, what must happen in order to maintain the same level of current flow?

Answer from: Quest

i think it’s a. this is because if they measured the mass of something with a mass of 150g, then their final answer would have to be approximately 150g. though all of their answers are almost 150, rosa and tran have the closest answers (or the exact answer) to the accurate one.

Answer from: Quest

car a and b are moving in opposite directions

plz mark.me the brainliest i rlly need this kind of yours in exchange

Which statements describe the motion of car a and car b? check all that apply.

Another question on Physics

Physics, 22.06.2019 13:20

Ahanging spring stretches by 35.0 cm when an object of mass 450 g is hung on it at rest. in this situation, we define its position as x = 0. the object is pulled down an additional 18.0 cm and released from rest to oscillate without friction. what is its position x at a moment 84.4 s later? express your answer in cm.

Answers: 1

Answer

Physics, 22.06.2019 21:10

Which of the following is a measure of the amount of light a star directly emits? a. luminosity b. intensity c. wavelength d. brightness

Answers: 2

Answer

Physics, 22.06.2019 21:30

A1500 w electric heater is plugged into the outlet of a 120 v circuit that has a 20 a circuit breaker. you plug an electric hair dryer into the same outlet. the hair dryer has power settings of 600 w, 900 w , 1200 w, and 1500 w. you start with the hair dryer on the 600 w setting and increase the power setting until the circuit breaker trips. under what setting does the circuit breaker trip.

Answers: 2

Answer

Physics, 23.06.2019 06:00

The frequency of a tuning fork can be found by the method shown. a long tube open at both ends is submerged in a beaker of water, and the vibrating tuning fork is placed near the top of the tube. the length l of the air column is adjusted by moving the tube vertically. the sound waves generated by the fork are reinforced when the length of the air column corresponds to one of the resonant frequencies of the tube. the smallest value for l for which a peak occurs in sound intensity is 7 cm. l what is the frequency of the tuning fork? the speed of sound in air is 345 m/s. answer in units of hz

Answers: 2

Answer

You know the right answer?

How do you change the currents in a circuit...

Questions