Physics, 29.10.2019 06:31 garcikyl000

•a −2.0 nc charge and a +2.0 nc charge are located on the x-axis at and , respectively. a. other than at infinity, is there a position or positions on the x-axis where the electric field is zero? if so, where? b. other than at infinity, at what position or positions on the x-axis is the electric potential zero? c. sketch graphs of the electric field strength and the electric potential along the x-axis.

Answers: 1

Show answers

Answers

Answer from: Quest

- measure reactants precisely. ( first choice)

- stir to the reaction take place. ( second choice)

- wait patiently until the reaction completes. ( fourth choice)

- make sure to recover as much copper as possible. ( last choice)

Answer from: Quest

force is based upon mass and acceleration.the statement is not always true.

it can be explained from newton's second law of motion.

as per newton's second law of motion the rate of change of momentum is directly proportional to the applied force and takes place along the direction of force.

mathematically it can be written as -

$f\alpha \frac{dp}{dt}$

⇒ $f= k \frac{dp}{dt}$

here k is the proportionality constant whose value is 1.

$f=\frac{dp}{dt}$

$f= \frac{d[mv]}{dt}$

$f= m\frac{dv}{dt} +v\frac{dm}{dt}$

$f=ma+v\frac{dm}{dt}$ [a is the acceleration=dv/dt]

hence we see that force not only depends on mass and acceleration but also on velocity and rate of change of mass. force f will depend on mass and acceleration only when mass is constant.

hence the statement that force is based upon mass and acceleration is false.

Answer from: Quest

The disturbance in a transverse wave is perpendicular to the wave motion.unlike a transverse wave, the disturbance in a longitudinal wave is parallel to the wave motion (a), that is, back and forth.

Answer from: Quest

Answerok the answer is (all)

Another question on Physics

Physics, 22.06.2019 11:50

The scalar triple product computes the magnitude m of the moment of a force vector f about a specified line. it is m = (r × f) · n, where r is the position vector from the line to the point of application of the force and n is a unit vector in the direction of the line. use matlab to compute the magnitude m for the case where f = [12, −5, 4] n, r = [−3, 5, 2] m, and n = [6, 5, −7].

Answers: 3

Answer

Physics, 22.06.2019 13:30

6–43 a food department is kept at 2128c by a refrigerator in an environment at 308c. the total heat gain to the food department is estimated to be 3300 kj/h and the heat rejection in the condenser is 4800 kj/h. determine the power input to the compressor, in kw and the cop of the refrigerator.

Answers: 2

Answer

Physics, 22.06.2019 23:10

An ascending elevator, hanging from a cable, is coming to a stop. part a part complete identify all forces acting on the elevator from the list below. select all that apply. select all that apply. kinetic friction normal force tension weight static friction submitprevious answers correct part b draw a free-body diagram of the object. draw the vectors starting at the black dot. the location and orientation of the vectors will be graded. the exact length of your vectors will not be graded but the relative length of one to the other will be graded.

Answers: 3

Answer

Physics, 23.06.2019 01:30

Amerry-go-round of radius r, shown in the figure, is rotating at constant angular speed. the friction in its bearings is so small that it can be ignored. a sandbag of mass m is dropped onto the merry-go-round, at a position designated by r. the sandbag does not slip or roll upon contact with the merry-go-round. how would you rank the following different combinations of m and r on the basis of the angular speed of the merry-go-round after the sandbag "sticks" to the merry-go-round from largest to smallest. a) m = 10kg, r = 0.25r b) m = 20kg, r = 0.25r c) m = 10kg, r = 0.50r d) m = 10kg, r = 1.0r e) m = 15kg, r = 0.75r f) m = 40kg, r = 0.25r

Answers: 1

Answer

You know the right answer?

•a −2.0 nc charge and a +2.0 nc charge are located on the x-axis at and , respectively. a. other tha...

Questions