Physics, 02.01.2020 20:31 paulinahunl17

Technician a says that the aspect ratio of a tire represents the relationship between the tire's cross-sectional height to its cross-sectional width. technician b says that low aspect ratios provide a softer ride because they will deflect more over irregular surfaces and under heavy loads. who is correct?
a. technician a
b. technician b
c. both a and b
d. neither a nor b

Answers: 1

Show answers

Answers

Answer from: johngayden46

Technician A

Explanation:

Often referred to as the profile or series, the aspect ratio of a tire is determined by dividing a tire’s section height by its section width when the tire is: inflated to maximum air pressure, mounted on the approved measuring rim, and under no load. This rules out Technician B.

A tire with a lower aspect ratio responds to lateral force more effectively than a tire with a higher aspect ratio. The aspect ratio affects steering stability. Generally, the shorter the sidewall, or the lower the aspect ratio, the less time it takes to transmit the steering input from the wheel to the tread. The result is quicker steering response. Aspect ratio also affects the tread contact patch. As a rule, a low-profile tire produces a wider tread contact patch. This wider tread contact patch creates a stiffer footprint that reduces distortion and provides improved cornering traction. Aspect ratio also impacts ride. A low-profile tire usually has a stiffer ride than the standard aspect ratio of 75 or more.

Technician a says that the aspect ratio of a tire represents the relationship between the tire's cro

Answer from: Quest

The objects are acted upon by only one force. gravity. mass times the acceleration of gravity (-9.81meters/second squared).

Answer from: Quest

force is based upon mass and acceleration.the statement is not always true.

it can be explained from newton's second law of motion.

as per newton's second law of motion the rate of change of momentum is directly proportional to the applied force and takes place along the direction of force.

mathematically it can be written as -

$f\alpha \frac{dp}{dt}$

⇒ $f= k \frac{dp}{dt}$

here k is the proportionality constant whose value is 1.

$f=\frac{dp}{dt}$

$f= \frac{d[mv]}{dt}$

$f= m\frac{dv}{dt} +v\frac{dm}{dt}$

$f=ma+v\frac{dm}{dt}$ [a is the acceleration=dv/dt]

hence we see that force not only depends on mass and acceleration but also on velocity and rate of change of mass. force f will depend on mass and acceleration only when mass is constant.

hence the statement that force is based upon mass and acceleration is false.

Another question on Physics

Physics, 21.06.2019 22:00

Atank holds 1000 gallons of water, which drains from the bottom of the tank in half an hour. the values in the table show the volume v of water remaining in the tank (in gallons) after t minutes.t(min) 5 10 15 20 25 30v(gal) 694 444 250 111 28 0(a) if p is the point (15, 250) on the graph of v, find the slopes of the secant lines pq when q is the point on the graph with t = 5, 10, 20, 25, and 30.(b) estimate the slope of the tangent line at p by averaging the slopes of two secant lines.(c) use a graph of the function to estimate the slope of the tangent line at p. (this slope represents the rate at which the water is flowing from the tank after 15 minutes.)show all steps.

Answers: 2

Answer

Physics, 21.06.2019 22:30

Abug is 12 cm from the center of a turntable that is rotating with a frequency of 45 rev/min . what minimum coefficient friction is required so that the bug stays on the turntable?

Answers: 1

Answer

Physics, 22.06.2019 03:00

An internally reversible refrigerator has a modified coefficient of performance accounting for realistic heat transfer processes of where qin is the refrigerator cooling rate, qout is the heat rejection rate, and is the power input. show that copm can be expressed in terms of the reservoir temperatures tc and th, the cold and hot thermal resistances rt,c and rt,h, and qin, as where rtot rt,c rt,h. also, show that the power input may be expressed as 1.39 a household refrigerator operates with cold- and hot-temperature reservoirs of tc 5 c and th 25 c, respectively. when new, the cold and hot side resistances are rc,n 0.05 k/w and rh,n 0.04 k/w, respectively. over time, dust accumulates on the refrigeratorâ€™s condenser coil, which is located behind the refrigerator, increasing the hot side resistance to rh,d 0.1 k/w. it is desired to have a refrigerator cooling rate of qin 750 w. using the results of problem 1.38, determine the modified coefficient of performance and the required power input w under (a) clean and (b) dusty coil conditions. internally reversible refrigerator qout qin w high-temperature reservoir low-temperature reservoir th th,i tc,i tc high-temperature side resistance low-temperature side resistance w qin th tc qinrtot tc qinrtot copm tc qinrtot th tc

Answers: 2

Answer

Physics, 22.06.2019 04:30

Idon’t quite understand this problem

Answers: 1

Answer

You know the right answer?

Technician a says that the aspect ratio of a tire represents the relationship between the tire's cro...

Questions