Physics, 03.06.2020 13:00 antlife555

Rank the following situations according to the pressure, from least to greatest. A.20 N exerted over a surface of 0.35 m2
B.20 N exerted over a surface of 0.65 m2
C.50 N exerted over a surface of 0.05 m2
D.50 N exerted over a surface of 0.35 m2
E.60 N exerted over a surface of 0.55 m2

HELP ME

Answers: 3

Show answers

Another question on Physics

Physics, 22.06.2019 12:40

Question part points submissions used suppose that 2 j of work is needed to stretch a spring from its natural length of 26 cm to a length of 36 cm. (a) how much work is needed to stretch the spring from 28 cm to 32 cm? (round your answer to two decimal places.)

Answers: 2

Answer

Physics, 22.06.2019 16:20

Select the correct answer. what does the process of natural selection involve?

Answers: 1

Answer

Physics, 23.06.2019 01:30

The flame produced by the burner of a gas (propane) grill is a pale blue color when enough air mixes with the propane (c3h8) to burn it completely. for every gram of propane that flows through the burner, what volume of air is needed to burn it completely? assume that the temperature of the burner is 195.0°c, the pressure is 1.05 atm, and the mole fraction of o2 in air is 0.210.

Answers: 2

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

Rank the following situations according to the pressure, from least to greatest. A.20 N exerted ove...

Questions