subject
Physics, 15.10.2020 06:01 abosse144

Help Me !! I have an exam. What will be velocity, when two bodies move in opposite direction?
1.Negative
2.Possitive
3.Zero
4. 1 and 2 both.

ansver
Answers: 1
Show answers

Another question on Physics

question
Physics, 22.06.2019 03:50
Two polarizers are oriented at 70∘∘ to one another. unpolarized light falls on them. what fraction of the light intensity is transmitted?
Answers: 1
Answer
question
Physics, 22.06.2019 09:30
Acar drives toward the right over the top of a hill, as shown below. which arrow represents the centripetal acceleration? w x y z
Answers: 3
Answer
question
Physics, 22.06.2019 23:30
With physics question #5? for any !
Answers: 1
Answer
question
Physics, 23.06.2019 01:00
Two point charges are separated by a certain distance. how does the strength of the electric field produced by the first charge
Answers: 2
Answer
You know the right answer?
Help Me !! I have an exam. What will be velocity, when two bodies move in opposite direction?
...
Questions
question
Engineering, 14.09.2019 02:10
The condition of irrotationality for a two-dimensional flow is satisfied when rotation w everywhere is (less than — equal to — more than) zero....
question
Engineering, 14.09.2019 02:10
The flow of a real fluid has (more —less - same ) complexity of an ideal fluid, owing to the phenomena caused by the existence of (viscosity-pressure...
question
Engineering, 14.09.2019 02:10
In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...
question
Engineering, 14.09.2019 02:10
Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...
question
Engineering, 14.09.2019 02:10
Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...
question
Engineering, 14.09.2019 02:10
Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...
question
Engineering, 14.09.2019 02:10
Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...
question
Engineering, 14.09.2019 02:10
Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...
question
Engineering, 14.09.2019 02:10
The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...
question
Engineering, 14.09.2019 02:10
Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...
question
Engineering, 14.09.2019 02:10
Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...
question
Engineering, 14.09.2019 02:10
Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...
question
Engineering, 14.09.2019 02:10
Draw and label a typical true stress-strain curve for a ductile material....
question
Engineering, 14.09.2019 02:10
Draw and label a typical engineering stress-strain curve for a brittle material....
question
Engineering, 14.09.2019 02:10
Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...
question
Engineering, 14.09.2019 02:10
Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...
question
Engineering, 14.09.2019 02:10
It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...
question
Engineering, 14.09.2019 02:10
For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...
question
Engineering, 14.09.2019 02:10
Which of the two materials (brittle vs. ductile) usually obtains the largest modulus of toughness and why?...
question
Engineering, 14.09.2019 02:10
Afour-cylinder chrysler si engine has the following characteristics: 2.2l displacement, 87.5 mm bore, 92 mm stroke, 8.9 compression ratio, and a maxi...
More questions: Physics Another questions
Questions on the website: 13722362
See results (0)