Physics, 25.02.2021 17:40 Arealbot

Explain the difference between potential energy, kinetic energy, and mechanical energy?

Answers: 3

Show answers

Answers

Answer from: jblac

Potential Eenergy is possessed by a body by virtue of its position relative to others, stresses within itself, electric charge, and other factors.kinetic energy is energy which a body possesses by virtue of being in motion. Mechanical energy is an energy that is possessed by an object due to its motion or due to its position

Explanation:

Answer from: Quest

most voltage drop calculators want the distance between the source and destination. then internally, they double it so both the source and return wires are calculated. but you need to know which distance the calculator uses so you're not half of what you should be or double what you should be.

most circuit breakers will not take a #6 directly, so the electrician will have to splice on a smaller pigtail. you also have to upsize the grounding wire when you upsized the ungrounded (hot) wire (see note in 250.122). this will preclude using most cable assemblies, as a cable with #6 copper will most likely only have a #10 grounding conductor. you need a #6 grounding conductor if the circuit is 20a. a #8 cable is no better, as it will have a #10 grounding conductor too. but most 20a breakers will take a #8 directly.

in your related post, you didn't say what type of load this is. if it is a light or heater, voltage drop won't be a big issue. if this is a motor, the current needs are huge at startup and the voltage drop can pose a problem. if this is a motor, knowing if the motor is under much load during startup will answer the voltage drop effect (a saw is easier to start than a compressor).

Answer from: Quest

the minimum constant speed at which she can catch the train is 2.7 m/s

given:

acceleration = 0.6 $\frac{m}{s^{2} }$

time = 4.5 s

to find:

velocity = ?

formula used:

from 1st kinematic equation we get,

v = u + at

u = initial speed of train = 0 m/s

v = final speed of the train

a = acceleration of the train

t = time

solution:

from 1st kinematic equation we get,

v = u + at

u = initial speed of train = 0 m/s

v = final speed of the train

a = acceleration of the train

t = time

v = 0 + (0.6 × 4.5)

v = 2.7 m/s

the minimum constant speed at which she can catch the train is 2.7 m/s

Another question on Physics

Physics, 21.06.2019 16:00

The rigid beam is supported by the three suspender bars. bars ab and ef are made of aluminum and bar cd is made of steel. if each bar has a cross-sectional area of 450 mm2, determine the maximum value of p if the allowable stress is (σallow)st = 200 mpa for the steel and ( σallow)al = 150 mpa for the aluminum. est = 200 gpa and eal = 70 gpa.

Answers: 2

Answer

Physics, 22.06.2019 01:10

Aparticle initially moving east with a speed of 20.0 m/s, experiences an acceleration of 3.95 m/s, north for a time of 8.00 s. what was the speed of the particle after this acceleration, in units of m/s? give the answer as a positive number.

Answers: 1

Answer

Physics, 22.06.2019 02:40

If the wheels lock when braking suddenly the vehicle: a: loses traction b: lose steering wheel ability c: gain speed slightly d: gain steering ability

Answers: 1

Answer

Physics, 22.06.2019 03:10

Athin plate moves between two parallel, horizontal, stationary flat surfaces at a constant velocity of v = 7.5 m/s. the two stationary surfaces are spaced 4 cm apart, and the medium between them is filled with oil whose viscosity is 0.9 n·s/m2. the part of the plate immersed in oil at any given time is 2 m long and 0.5 m wide. if the plate moves through the mid-plane between the surfaces, determine the force required to maintain this motion. what would your response be if the plate was 1 cm from the bottom surface (h2) and 3 cm from the top surface (h1)? if the plate moves through the mid-plane between the surfaces, the force required to maintain the motion will be n. if the plate was 1 cm from the bottom surface (h2) and 3 cm from the top (h1) surface, the force required to maintain the motion would be n.