Answers: 1
Physics, 22.06.2019 17:00
If you wanted to move an electron from the positive to the negative terminal of the battery, how much work w would you need to do on the electron? enter your answer numerically in joules.
Answers: 1
Physics, 23.06.2019 00:50
Aplayer uses a hockey stick to push a puck at a constant velocity across the ice. the weight of the puck is 170 n. the coefficient of friction is 0.0600. with what force must the player push the puck so that his force just equals the frictional force? 28.3 n 0.999 n 0.102 n 0.0104 n
Answers: 1
Physics, 23.06.2019 05:00
Which factor listed below most likely results in the loss of genetic variation from small populations? question 2 options: mutation migration genetic recombination genetic drift
Answers: 3
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
In Young experiment, a light with a wavelength of 410 nm falls on two slits
separated by 0.03 mm,...
Chemistry, 13.07.2019 15:00
Biology, 13.07.2019 15:00
Mathematics, 13.07.2019 15:00
Health, 13.07.2019 15:00
Physics, 13.07.2019 15:00
Physics, 13.07.2019 15:00
Health, 13.07.2019 15:00
Health, 13.07.2019 15:00
Health, 13.07.2019 15:00
Chemistry, 13.07.2019 15:00
Mathematics, 13.07.2019 15:00