SAT, 08.10.2021 09:50 gael6529

How would the author of Passage 1 MOST LIKELY describe the argument in
Passage 2? Giving brainlest

Answers: 3

Show answers

Another question on SAT

SAT, 27.06.2019 12:00

Use the rule of 72 to calculate how long it will take for your money to double if its earning 6% in interest. a. 12yrs b. 16yrs c. 36yrs d. 72yrs

Answers: 2

Answer

SAT, 27.06.2019 12:00

What is an example of a college admissions test? -state test -cat -act -personality test

Answers: 1

Answer

SAT, 28.06.2019 17:30

Host danny boyle used a line from what shakespearean play to welcome the athletes and fans arriving in london for the 2012 olympics?

Answers: 1

Answer

SAT, 29.06.2019 03:30

After bill is passed in congress where is bill's next stop?

Answers: 1

Answer

You know the right answer?

How would the author of Passage 1 MOST LIKELY describe the argument in
Passage 2? Giving bra...

Questions

Engineering, 11.07.2019 05:10

Air is compressed by a compressor from v1= 1.0 m^3/kg to v2= 0.71 m^3/kg in a reversible, isothermal process. the air temperature is maintained consta...

Engineering, 11.07.2019 05:10

Someone shoots an arrow upward. the arrow reaches a maximum height of 100 feet. a)-what is the initial velocity of the arrow? b)- at what time will t...

Engineering, 11.07.2019 05:10

What size (inner diameter) of concrete pipe (with e-0.005) is required to carry water (at 60°f) at a discharge rate of 15 ft3/s and with a head loss o...

Engineering, 11.07.2019 05:10

Water if flowing steadily in a 0.6-m wide rectangular open channel at a rate of 0.3 m^3/s. if the depth is 0.15 m, a)-determine i) the flow velocity,...

Engineering, 11.07.2019 05:10

An elevated water tower is used to supply water to a city. to make water available at a pressure of 400 kpa at a ground level location within the city...

Engineering, 11.07.2019 05:10

What is considered a uselapplication of modal analysis? (1) identifying the rigid body modes (2) finding modal frequencies (3) obtaining the modal am...

Engineering, 11.07.2019 05:10

Arefrigeration cycle rejects qn 500 btu/s to a hot reservoir at 540 r, while receiving c200 btu/s at 240°r. this refrigeration cycle a)- is internally...

Engineering, 11.07.2019 05:10

Acylindrical specimen of some metal alloy having an elastic modulus of 117 gpa and an original cross-sectional diameter of 3.6 mm will experience only...

Engineering, 11.07.2019 05:10

Arigid, insulated tank that is initially evacuated is connected through a valve to a supply line that carries steam at 3.5 mpa. now the valve is opene...

Engineering, 11.07.2019 05:10

Aheat pump, using ammonia as the refrigerant, has the following conditions , heat effect 75,000kj/sec , evaporator pressure 0.22mpa , condenser pressu...

Engineering, 11.07.2019 05:10

A2.5 cm diameter horizontal water jet with a speed of vi- 40 m/s relative to the ground is deflected by a 60° stationary cone whose base diameter is 2...

Engineering, 11.07.2019 05:10

For a specified inlet state, exit pressure and mass flowrate, the power input of a that of an compressor operating adiabatically and at steady state w...

Engineering, 11.07.2019 05:10

Asingle-cylinder four-stroke-cycle spark- ignition engine has a bsfc of 0.4 kg/kw-hr and a volumetric efficiency of 78% at a speed of 45 rps. the bore...

Engineering, 11.07.2019 05:10

Heat in the amount of 100 kj is transferred directly from a hot reservoir at 1200 k to a cold reservoir at 600k. calculate the entropy change of the t...

Engineering, 11.07.2019 05:10

A1m by 1m square gate is to be located on one vertical side of a tank that will contain 2 m depth of water up to the bottom of the gate. determine the...

Engineering, 11.07.2019 05:10

Acylindrical metal specimen having an original diameter of 11.80 mm and gauge length of 51.7 mm is pulled in tension until fracture occurs. the diamet...

Engineering, 11.07.2019 05:10

Air is compressed in an isentropic process from an initial pressure and temperature of p1 = 90 kpa and t1=22°c to a final pressure of p2=900 kpa. dete...

Engineering, 11.07.2019 05:10

Is a process that is internally reversible and adiabatic necessarily isentropic? explain using an equation....

Engineering, 11.07.2019 05:10

After the formation of cells is finished, a cellular manufacturing system can use either a decoupling or an integrating approach to manage the materia...

Engineering, 11.07.2019 05:10

Apipe system consists of a lower section with two 90° elbows and an upper section with a 180° bend and two straight flow tees. if the flow is measured...

How would the author of Passage 1 MOST LIKELY describe the argument in Passage 2? Giving brainlest

Answers

Another question on SAT

How would the author of Passage 1 MOST LIKELY describe the argument in
Passage 2? Giving brainlest